Keysight Technologies N5290A Скачать руководство пользователя страница 19

Страница: 19 / 96

Keysight N5290/1A Service Guide 1-13

Safety and Regulatory Information
Environmental Requirements

Environmental Requirements

The environmental requirements shown below are characteristic for the system
and are based on the limitations of the PNA network analyzer used.

System Heating and Cooling

Install air conditioning and heating, if necessary, to maintain the ambient

temperature within the appropriate range (as given in the table above). Air

conditioning capacity must be consistent with the BTU ratings given in

Table

1-1 on page 12

and

Table 1-2 on page 13

Ventilation Requirements: When installing the product in a cabinet, the

convection into and out of the product must not be restricted. The ambient

temperature (outside the cabinet) must be less than the maximum

operating temperature of the instrument by 4 °C for every 100 watts

dissipated in the cabinet. If the total power dissipated in the cabinet is

greater than 800 watts, then forced convection must be used

Table 1-2

N5290/1A Environmental Conditions (Operating)

Environment

Temperature

Operation

C to 40

C (41

F to 104

Storage

–40

C to +65

C (–40

F to 158

Measurement Calibration

C to 26

C (68

F to 79

Performance Verification

Temperature must be within 1

C (1.8

F) of

the temperature at which the measurement

calibration was performed.

Relative Humidity

Type tested at 95%, +40

C (non-condensing)

Pressure Altitude

Type tested 0 to 4600 meters (~15,000 feet)

Table 1-3

N5292A Environmental Conditions (Operating)

Environment

Temperature

for indoor use only (unless specified otherwise.)

Altitude up to

4,600 meters

Temperature

0 to 40 °C

Relative humidity

Type tested, 0 to 95% relative humidity,

non-condensing up to 40°C

Содержание N5290A

































































































Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды

Keysight Technologies N5290A, Руководство по установке

Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды