Keysight Technologies N5290A Скачать руководство пользователя страница 49

Страница: 49 / 96

3-1

Keysight N5290/1A PNA/PNA-X Series
2-Port and 4-Port Microwave Network Analyzer System

Installation Guide

System Installation

Information in This Chapter

This chapter describes preparing to receiving your 2-port or 4-port N5290/1A

millimeter system and the system’s installation procedure(s).

Chapter Three at-a-Glance

IMPORTANT!

A 85059B 1.0 mm Precision Calibration Kit and a 85059V 1.0 mm Precision

Verification Kit are required to complete the installation of the N5290/1A

Millimeter-wave Systems.
In order to maintain compliance to the certificate of calibration it is

recommended that the frequency extenders be connected to the

corresponding test set ports per the Certificate of Calibration provided.

Section Title

Summary of Content

“Getting Prepared” on page 2

Discusses how to download the service guide, tools required for

installation, and the time required to install the system.

“Getting Assistance from Keysight”

on page 3

How to contact Keysight for support with your system.

“Receiving the System” on page 4

What to do when you receive your system, verifying the parts received,

and customer engineering support.

“PNA, Controller, and Test Head

Module Interconnections” on

page 6

A discussion and procedures for assembling your N5290/1A system.

“Initializing the N5290/1A

Broadband System” on page 22

Discusses how to initialize the N5290/1A system.

“Running the Installation

Calibration” on page 23

Describes the N5290/1A millimeter wave installation calibration.

“Troubleshooting the N5293/5A

Millimeter Modules” on page 26

Describes the types of error messages that might be seen, if a

millimeter wave module is incorrectly installed.

Содержание N5290A

































































































Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды

Keysight Technologies N5290A, Руководство по установке

Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды