Keysight Technologies N5290A Скачать руководство пользователя страница 11

Страница: 11 / 96

Keysight N5290/1A Service Guide 1-5

Safety and Regulatory Information
General Safety Considerations

Servicing

These servicing instructions are for use by qualified personnel only.

To avoid electrical shock, do not perform any servicing unless you

are qualified to do so.

Danger of explosion if battery is incorrectly replaced. Replace only

with the same or equivalent type recommended. Discard used

batteries according to local ordinances and/or manufacturer’s

instructions.

Procedures described in this document may be performed with

power supplied to the product while protective covers are removed.

Energy available at many points may, if contacted, result in personal

injury.

The power cord is connected to internal capacitors that may remain

live for 10 seconds after disconnecting the plug from its power

supply.

Install the instrument so that the detachable power cord is readily

identifiable and is easily reached by the operator. The detachable

power cord is the instrument disconnecting device. It disconnects

the mains circuits from the mains supply before other parts of the

instrument. The front panel switch is only a standby switch and is

not a LINE switch. Alternatively, an externally installed switch or

circuit breaker (which is readily identifiable and is easily reached by

the operator) may be used as a disconnecting device.

Do not operate the analyzer with the outer cover removed for more than

30 minutes, as this could cause the analyzer to overheat which could

result in costly damage.

The opening of covers or removal of parts may expose dangerous

voltages. Disconnect the instrument from all voltage sources while

it is being opened.

There are no replaceable fuses in the mains input or within the power

supply assembly.

Keysight personnel: after calibration is completed, attach four “calibration

void if seal broken” stickers to the PNA as shown in

Figure 1-1

Содержание N5290A

































































































Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды

Keysight Technologies N5290A, Руководство по установке

Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды