Keysight Technologies N5290A Скачать руководство пользователя страница 4

Страница: 4 / 96

4 Keysight N5290/91A Installation Guide

Front Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

IF Ref Out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

IF Test Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

1 / 2/ 3/ 4 (Integrated Connector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

Source In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

Low Band. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

On/Standby Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

Active LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

Rear Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

IF OUTPUTS – SMA (female). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

LO IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

Test Set I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

Line Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

Power Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

Compatible Millimeter-Wave Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

N5293/5A Millimeter-Wave Test Head Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20

Active LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20

Basic System Measurement Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22

Coaxial Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22

3. System Installation

Information in This Chapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Chapter Three at-a-Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Getting Prepared . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Tools Required for the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
About Installing the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Getting Assistance from Keysight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Contacting Keysight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Receiving the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Receiving the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Keysight Technologies Customer Engineering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Review the Principles of Connector Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

PNA, Controller, and Test Head Module Interconnections. . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

System Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Mounting a Network Analyzer on the Test Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

N5290/1A Option 201 (Interconnect Kit N5292-60012) . . . . . . . . . . . . . . . . . . . . . . 3-13

N5290/1A Option 202 (Interconnect Kit N5292-60013) . . . . . . . . . . . . . . . . . . . . . . 3-14

N5290/1A Option 401 or N5290/1A Option 402—(Interconnect Kit N5292-60016). 3-15

N5290/1A Option 403—(Interconnect Kit N5292-60017) . . . . . . . . . . . . . . . . . . . . . 3-16

Rear Panel Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
N5293/5A Modules Front Panel Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

Connections for Each Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

N5292A Option 200 2–Port Cable Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

Содержание N5290A

































































































Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды

Keysight Technologies N5290A, Руководство по установке

Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды