Keysight Technologies N5290A Скачать руководство пользователя страница 29

Страница: 29 / 96

Keysight N5290/1A Installation Guide 2-5

System Description
N5290/1A Network Analyzer Millimeter-wave System

Figure 2-3

N5291A System Options

System Description

Introduction

This section of this document describes the broadband millimeter-wave

system using an N5292A Millimeter Head Controller. Banded millimeter-wave

systems are made up of three types of major components: a PNA or PNA-X, a

controller test set, and millimeter-wave heads. These components are

assembled into a system at the customer's site. This section of the document

focuses on receiving the controller with accessories and then on system

installation and operation.

Table 2-1 on page 2-7

and

Table 2-2 on page 2-7

list compatible PNA and

PNA-X models with required options.

Table 2-3 on page 2-8

and

Table 2-4 on

page 2-9

list available millimeter-wave modules. Typical system configurations

are pictured in

Figure 2-4 on page 6

and

Figure 2-5 on page 6

The N5292A Millimeter Head Controller is also used as part of the N5290/1A

broadband analyzer system. Refer to

“N5292A Test Controller Description” on

page 2-16

Содержание N5290A

































































































Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды

Keysight Technologies N5290A, Руководство по установке

Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды