Keysight Technologies N5290A Скачать руководство пользователя страница 55

Страница: 55 / 96

Keysight N5290/1A Installation Guide 3-7

System Installation
PNA, Controller, and Test Head Module Interconnections

1. On the PNA

: Remove the feet from the bottom of the analyzer.

Remove the 2 lower standoffs from the rear panel on the analyzer.

Remove the top two standoffs from the rear panel on the test set.

Figure 3-1

Rear Bottom Feet

Install the two rear locking feet (N5240-20092 and N5240-20095) or

(N5240-20093 and N5240-20094) onto the analyzer, where the standoffs

were removed using 0515-1619 screws. Use T-20 to torque to 21 in-lbs.

Optional: Rotate the PNA 180 degrees to install locking feet. Refer to

Figure 3-2 on page 8

The network analyzer is heavy. It is recommended that two

individuals, or a mechanical lift be used to lift or transport the

instrument.

Содержание N5290A

































































































Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды

Keysight Technologies N5290A, Руководство по установке

Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды