Keysight Technologies N5290A Скачать руководство пользователя страница 52

Страница: 52 / 96

3- 4 Keysight N5290/1A Installation Guide

System Installation
Receiving the System

Receiving the System

The N5290/1A system components will arrive packaged separately. For a

complete list of components shipped with your system, refer to

Table 2-3 on

page 2-8

through

Table 2-4 on page 2-9

When the entire shipment has arrived, contact Keysight Technologies to

arrange for system installation. See

“Keysight Support, Services, and

Assistance” on page 4-4

Keep the shipping containers until the system checklist has been completed,

and the system has been checked for physical damage.
If the shipping container is damaged or the packaging material shows signs of

stress, notify the carrier as well as Keysight Technologies. Keep the shipping

materials for the carrier’s inspection. Keysight Technologies will arrange for

repair or replacement of damaged equipment without waiting for a claim

settlement from the carrier. Refer to

“Keysight Support, Services, and

Assistance” on page 4-4

Keysight Technologies Customer Engineering

A Keysight Technologies Customer Engineer will be assigned to help you install

the system. During installation, the Customer Engineer will do the following:

— Unpack the system components.
— Verify the system parts list, see

Table 2-3 on page 2-8

Table 2-4 on

page 2-9

— Initialize the PNA as described in E8356-90001 Quick Start Guide that

comes with every PNA.

— Run the Operator’s Check of the PNA as described in the E8356-90001

Quick Start Guide that comes with every PNA.

— Connect the N5292A millimeter head controller to the PNA. Install the

N5293A or N5295A millimeter-wave frequency extender test head modules.

— Run the Operator’s Check of the system using the procedure in

Chapter 4,

“Performance Verification.”

— Run the System Verification as described in

Chapter 4, “Performance

Verification.”

— Provide training for one user.

The N5292A millimeter head controller and the test head modules are

sensitive to electrostatic discharge (ESD). Ground your work station before

unpacking and installing the test head modules. See

“Electrostatic

Discharge Protection” on page 1-7

Содержание N5290A

































































































Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды

Keysight Technologies N5290A, Руководство по установке

Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды