
8
TK-5710
(
B
)
/5710H
(
B
)
No.
Setup item
Display
Remarks
1
Select Zone/Channel
∗ ∗
-
∗ ∗ ∗
Zone : 1~50, Channel : 1~250
2
RX Frequency
1
∗ ∗
.
∗ ∗ ∗ ∗ ∗
MHz
Receive frequency
3
TX Frequency
1
∗ ∗
.
∗ ∗ ∗ ∗ ∗
MHz
Transmit frequency
4
Channel Type
TYPE
ANALOG/APCO/MIXED
5
TX Mode
MODE
ANALOG/APCO
6
Channel Spacing
SPACE
25.0kHz/12.5kHz (When the Channel type is selected "ANALOG" or "MIXED".)
APCO 12.5kHz/12.5kHz (When the Channel type is selected "APCO".)
7
RX Signaling
RX-SIG
Receive QT/DQT
8
TX Signaling
TX-SIG
Transmit QT/DQT
9
RX NAC
RX-NAC
∗ ∗ ∗
000~FFF (Hexadecimal)
Note:"F7F" cannot be set.
10
TX NAC
TX-NAC
∗ ∗ ∗
000~FFF (Hexadecimal)
Note:"F7E" and "F7F"cannot be set.
11
Talkgroup List No.
None
When you do not want to set the Talkgroup list number to the transceiver.
∗ ∗ ∗
Talkgroup list number (1~250)
(When the Talkgroup list name is not set to the transceiver.)
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
Talkgroup list name (12 digits)
(When the Talkgroup list name is set to the transceiver.)
The setup items for self programming mode are as follows.
9. Self Programming Mode
Write mode for frequency data and signaling etc. To be
used ONLY by the authorized service person maintaining the
user's equipment. After programming, reset the FPU to the
"Self- Programming" disabled mode. Transceivers CANNOT
be delivered to the end-user in the self-programming mode.
The following setup items in the channels programmed by
the FPU can be changed using the self-programming mode.
The addition of new channel and the deletion of channel that
has already been programmed by the FPU cannot be
performed using the self-programming mode.
• RX Frequency
• TX Frequency
• Channel Type
• TX Mode (When the channel type is selected "MIXED".)
• Channel Spacing
• RX Signaling
• TX Signaling
• RX NAC
• TX NAC
• Talkgroup List No.
Note:
The personality will be also changed when the above-
mentioned items is changed. (Refer to the FPU for the
personality details.)
9-1. Enter to the self programming mode
Press and hold the [GRP^] key while turning the trans-
ceiver power ON. Ignoring whether the Read authorization
password is set or not, "PASSWORD" appears.
If the Read authorization password is not set to the trans-
ceiver, "SELF PG MODE" is displayed on the LCD when the
[PF2] key is pressed while "PASSWORD" is displayed.
If the password is set to the transceiver, "SELF PG MODE"
is displayed on the LCD when you enter the correct pass-
word while "PASSWORD" is displayed.
For the password input method, see "8. Clone Mode”
step 3 described on page 7.
Note :
This mode (self programming mode) cannot be set when
it has been disabled with the FPU.
9-2. Data writing
If the [PF4] key is pressed while Zone/Channel mode is
displayed, new data is written into memory. "WRITING" is
displayed while the transceiver is writing data.
REALIGNMENT