
17
TK-5710
(
B
)
/5710H
(
B
)
INSTALLATION
8. External Speaker (KES-5/6:Option)
The speaker output from the transceiver is as follows:
1. The KCH-14 has a built-in speaker (3W/8 ohms).
2. The KCH-15 does not have a built-in speaker.
3. The external speaker output from the accessory
connector (9-pin) on the rear of the transceiver is 13W/4
ohms. Use the KES-5 or KES-6.
4. The speaker output from the accessory connector (12-
pin) on the rear of the control head is 2W/4 ohms. If the
remote kit (KRK-5, KRK-6DH) is used, use the KES-5 or
KES-6.
Note :
Since the transceiver uses a BTL audio amplifier, do not
ground the speaker output pin.
8-1. Connecting the KES-5/6 external speaker to
the transceiver
• When taking the AF output from the accessory
connector (9-pin) on the rear of the transceiver
The following tools are required for changing the
connector.
Extracting tool
The following extracting tool is recommended :
Molex Inc. Order No. : 11-03-0002
1. Remove the short plug from the accessory connector (9-
pin) on the rear of the transceiver (Fig. 8-1-1).
Note : Save the jumper, which is required when the
transceiver is used without the external speaker.
2. Remove the terminals with the jumper from the
connector housing holes number 3 and 6 using the
extracting tool.
Removing the jumper lead (Fig. 8-1-2)
1) Insert the extracting tool (11-03-0002) into the
connector while pushing the jumper lead in the
direction of (a).
2) Push the extracting tool into collapse the barbs of the
crimp terminal.
3) Pull out the lead while continuing to push the
extracting tool in the direction (b).
3. Reinsert the terminal with the black and white stripe lead
into hole number 2, and the terminal with the black lead
into hole number 6 (Fig. 8-1-3).
4. Connect the short plug to the accessory connector (9-pin)
on the rear of the transceiver.
Fig. 7-2
Solder land
Component side of the Control unit
ANI board
BUSY (Channel busy signal output)
AKEY (Key input)
NC (No connection)
NC (No connection)
NC (No connection)
PTOA (PTT output)
NC (No connection)
EMG (Emergency signal output)
E (GND)
E (GND)
NC (No connection)
NC (No connection)
E (GND)
5C (5V)
STON (Side tone input)
ATXI (Data input)
TCONT (Speaker mute signal input)
NC (No connection)
AINH (MIC mute signal input)
AUX I/O (Emergency signal input)
NC (No connection)
NC (No connection)
NC (No connection)
NC (No connection)
NC (No connection)
8C (8V)
ANI board
Voice scrambler
board
(Connector type)
Voice scrambler
board
(Lead wire type)
CN771
3M double coated cushion
No.4008 (or No.4408)
25 x 25 mm
3M double coated cushion
No.4032 (or No.4432)
25 x 25 mm
3M double
coated cushion
No.4008
(or No.4408)
25 x 25 mm
Fig. 7-1
Extracting tool
(11-03-0002)
Jumper lead
(a)
(b)
Barbs
Crimp terminal
Short plug
(E37-0733-05)
Fig. 8-1-1
Fig. 8-1-2
7. ANI Board Connection
1. Remove the upper case and upper packing of the
transceiver.
2. Attach the cushion to the ANI board as shown in Fig.7-2.
3. Solder each lead wire of the ANI board to a necessary
location of each landing on the component side of the
control unit.
Note:
You must setup using the KPG-95D.