Kentrox RMX-3200 Скачать руководство пользователя

Страница: 172 / 388

Remote RMX-3200 Version 5.2x Configuration Guide

Configuring Measurements and the Measurement Table: Configuring a Measurement Table Entry for
State Transitions and Durations

16-10

Configuring a Measurement Table Entry for State
Transitions and Durations

To configure a measurement table entry that tracks the number of times the alarm
table entry ExtTemp1 transitions to the major state:

1. At the main prompt, configure measurement table entry

ExtTemp1_Transitions

with description

Number of External temperature high alarms

config meas-table entry ExtTemp1_Transitions description Number of

External temperature high alarms

2. Configure the originator for this measurement with the following settings:



Measurement function

@state-transitions



Originator

alarm-entry ExtTemp1



Active state

major

config meas-table entry ExtTemp1_Transitions originator @state-

transitions (alarm-entry ExtTemp1, major)



Note:

The measurement function

@state-duration

can be used to measure

the number of seconds an alarm is in the specified active state.

3. (optional) Verify that the measurement table entry has been configured properly:

show meas-table entries ExtTemp1_Transitions

In this scenario, you will:



Configure a measurement table entry with name and description



Configure the originator to use the

@state-transitions

function to measure

the number of state transitions

Содержание RMX-3200




































































































































































































































































































































































































Результаты поиска

Содержание RMX-3200

Отзывы:

Похожие инструкции для RMX-3200

Бренды по названию

Популярные бренды

Kentrox RMX-3200, Руководство по настройке

Результаты поиска

Содержание RMX-3200

Отзывы:

Похожие инструкции для RMX-3200

Бренды по названию

Популярные бренды