Keithley 2701 Скачать руководство пользователя | Manualshive

Страница: 101 / 168

background image

Model 2701 Service Manual

Disassembly

5-5

Remove all the connections except the front AMPS connection by pulling the wires off
the pin connectors. To remove the front panel AMPS input wire (white), first remove
the AMPS fuse holder, then use needle-nose pliers to grasp the AMPS wire near the
fuse housing. Push the wire forward and down to snap the spring out of the fuse hous-
ing. Carefully pull the spring and contact tip out of the housing.

4.

Unplug cables:

•

Unplug the display board ribbon cable from connector J1014.

•

Unplug the transformer cables from connectors J1002 and J6.

•

Unplug scanner slots ribbon cable from connector J1012.

•

Unplug analog backplane connections J1008 and J1010.

•

Unplug the battery cable from J1017.

•

Unplug the fan cable from J1018.

5.

Remove the fastening screws that secure the motherboard to the chassis. One of these
screws is located along the left side of the unit towards the middle and it also secures
U144. One screw is located at the right center of the chassis near the front/rear switch,
S101, and another screw is behind the AC shield. The final screw is near the rear panel
next to J5.

During re-assembly, replace the board and start the RS-232 and Digital I/O connector
nuts and the mounting screw. Tighten all the fasteners once they are all in place and the
board is correctly aligned.

6.

Remove the motherboard, which is held in place by edge guides on one side, by sliding
it forward until the board edges clear the guides. Carefully pull the motherboard from
the chassis.

Card cage removal

After the motherboard has been removed, the card cage that holds plug-in modules can be

removed simply by removing the screws that attach the card cage to the case bottom and
removing it.

Front panel disassembly

Use the following procedures to remove the display board and/or the pushbutton switch pad:

NOTE

You must first remove the case cover, the front/rear input switch, and the front input
terminal wires as described earlier in this section.

1.

Unplug the display board ribbon cable from connector J1014.

2.

Remove the front panel assembly.

This assembly has four retaining clips that snap onto the chassis over four pem nut
studs. Two retaining clips are located on each side of the front panel. Pull the retaining
clips outward and, at the same time, pull the front panel assembly forward until it
separates from the chassis.

«
...
99
100
101
102
103
...
»

Содержание 2701









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2701

Бренд: Moog Страницы: 109

Бренд: Philex Страницы: 2

Бренд: East Tester Страницы: 51

Бренд: NEC Страницы: 33

Бренд: Surtek Страницы: 36

Бренд: Jeulin Страницы: 24

Бренд: Jeulin Страницы: 20

Бренд: IDEAL INDUSTRIES Страницы: 21

Бренд: Amprobe Страницы: 92

Бренд: Owon Страницы: 33

Бренд: UNI-T Страницы: 34

Бренд: GB Instruments Страницы: 11

Бренд: Mastech Страницы: 24

Бренд: Mastech Страницы: 10

Бренд: 3B SCIENTIFIC Страницы: 8

Бренд: PANCONTROL Страницы: 221

Бренд: National Instruments Страницы: 128

Бренд: Major tech Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды