Keithley 2701 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 168

background image

3-2

Routine Maintenance

Model 2701 Service Manual

Introduction

The information in this section deals with routine type maintenance and includes procedures

for setting the line voltage, replacing the Model 2701 line and front terminal AMPS fuses, and
replacing the amps fuses for the Model 7700 plug-in module. Replacement of the Model 2701
non-volatile RAM battery and module relay closure count is also covered.

Setting the line voltage and replacing the line fuse

WARNING

Disconnect the line cord at the rear panel and remove all test leads con-
nected to the instrument (front and rear) before replacing the line fuse.

The power line fuse is located in the power module next to the AC power receptacle (see

Figure 3-1

). If the line voltage must be changed or if the line fuse requires replacement, per-

form the following steps:

1.

Place the tip of a flat-blade screwdriver into the power module by the fuse holder
assembly (see

Figure 3-1

). Gently push in and to the left. Release pressure on the

assembly and its internal spring will push it out of the power module.

2.

Remove the fuse and replace it with the type listed in

Table 3-1

.

CAUTION

For continued protection against fire or instrument damage, replace the
fuse only with the type and rating listed. If the instrument repeatedly
blows fuses, locate and correct the cause of the trouble before replacing the
fuse.

3.

If configuring the instrument for a different line voltage, remove the line voltage selec-
tor from the assembly and rotate it to the proper position. When the selector is installed
into the fuse holder assembly, the correct line voltage appears inverted in the window.

CAUTION

Operating the Model 2701 on the wrong line voltage may result in
instrument damage.

4.

Install the fuse holder assembly into the power module by pushing it in until it locks in
place.

«
...
69
70
71
72
73
...
»

Содержание 2701









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2701

Бренд: Klein Tools Страницы: 12

Бренд: Mastech Страницы: 14

Бренд: Mastech Страницы: 18

Бренд: Morris Страницы: 13

Бренд: Morris Страницы: 9

Бренд: Zico Страницы: 6

Бренд: Beijing Huahuan Electronics Страницы: 28

METRAHIT T-COM PLUS

Бренд: Gossen MetraWatt Страницы: 76

Бренд: CTC Union Страницы: 50

Бренд: Delta Страницы: 3

Бренд: IDEAL INDUSTRIES Страницы: 9

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 32

Бренд: Mastech Страницы: 10

Бренд: LIMIT Страницы: 96

Бренд: VOLTCRAFT Страницы: 118

Бренд: Samsung Страницы: 69

Бренд: Actisense Страницы: 6

Бренд: TC Communications Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды