Keithley 2700 Скачать руководство пользователя | Manualshive

Страница: 83 / 174

background image

Troubleshooting

4-3

Front panel tests

There are two front panel tests: one to test the functionality of the front panel keys and one

to test the display. In the event of a test failure, refer to “Display board checks” for details on
troubleshooting the display board.

KEY test

The KEY test allows you to check the functionality of each front panel key. Perform the fol-

lowing steps to run the KEY test:

1.

Press SHIFT and then TEST to access the self-test options.

2.

Use the up or down RANGE key to display “TEST: KEY”.

3.

Press ENTER to start the test. When a key is pressed, the label name for that key is dis-
played to indicate that it is functioning properly. When the key is released, the message
“NO KEY PRESS” is displayed.

4.

Pressing EXIT tests the EXIT key. However, the second consecutive press of EXIT
aborts the test and returns the instrument to normal operation.

DISP test

The display test allows you to verify that each segment and annunciator in the vacuum fluo-

rescent display is working properly. Perform the following steps to run the display test:

1.

Press SHIFT and then TEST to access the self-test options.

2.

Use the up or down RANGE key to display “TEST: DISP”.

3.

Press ENTER to start the test. There are four parts to the display test. Each time
ENTER is pressed, the next part of the test sequence is selected. The four parts of the
test sequence are as follows:

a.

All annunciators are displayed.

b.

The segments of each digit are sequentially displayed.

c.

The 12 digits (and annunciators) are sequentially displayed.

d.

The annunciators located at either end of the display are sequentially displayed.

4.

When finished, abort the display test by pressing EXIT. The instrument returns to nor-
mal operation.

«
...
81
82
83
84
85
...
»

Содержание 2700















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2700

Бренд: Hameg Страницы: 56

Бренд: Ultra electronics Страницы: 2

MultiMeter-Home

Бренд: LaserLine Страницы: 68

Бренд: Keysight Страницы: 177

Бренд: UNI-T Страницы: 36

Бренд: PEWA Страницы: 66

Бренд: Mastech Страницы: 15

Бренд: Mastech Страницы: 16

Бренд: Raisecom Страницы: 273

Бренд: IDEAL Страницы: 14

Бренд: Raytech Страницы: 40

Бренд: Omega Страницы: 18

Бренд: Velleman Страницы: 9

Бренд: UNI-T Страницы: 36

Бренд: Testboy Страницы: 244

Бренд: Sanwa Страницы: 82

Бренд: Kopp Страницы: 84

Бренд: DER EE Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды