Keithley 2700 страница 127 Скачать руководство пользователя | Manualshive

Страница: 127 / 174

background image

Specifications

A-7

GENERAL SPECIFICATIONS:

POWER SUPPLY: 100V / 120V / 220V / 240V ±10%.

LINE FREQUENCY: 45Hz to 66Hz and 360Hz to 440Hz, automatically sensed at power-up.

POWER CONSUMPTION: 28VA.

OPERATING ENVIRONMENT: Specified for 0°C to 50°C. Specified to 80% RH at 35°C.

STORAGE ENVIRONMENT: –40°C to 70°C.

BATTERY: Lithium battery-backed memory, 3 years @ 23°C.

WARRANTY: 3 years.

EMC: Conforms to European Union Directive 89/336/EEC EN61326-1.

SAFETY: Conforms to European Union Directive 73/23/EEC EN61010-1.

VIBRATION: MIL-PRF-28800F Class 3, Random.

WARM-UP: 2 hours to rated accuracy.

DIMENSIONS:

Rack Mounting: 89mm high

×

213mm wide

×

370mm deep (3.5 in

×

8.375 in

×

14.563 in).

Bench Configuration (with handle and feet): 104mm high

×

238mm wide

×

370mm deep (4.125 in

×

9.375 in

×

14.563 in).

SHIPPING WEIGHT: 6.5kg (14 lbs.).

DIGITAL I/O: 2 inputs, 1 for triggering and 1 for hardware interlock. 5 outputs, 4 for Reading Limits and 1 for Master Limit. Outputs are TTL com-

patible or can sink 250mA, diode clamped to 33V.

TRIGGERING AND MEMORY:

Window Filter Sensitivity: 0.01%, 0.1 %, 1%, 10%, or Full-scale of range (none).

Reading Hold Sensitivity: 0.01%, 0.1 %, 1%, or 10% of reading.

Trigger Delay: 0 to 99 hrs (1ms step size).

External Trigger Delay: <2ms.

External Trigger Jitter: <1ms.

Memory Size: 55,000 readings.

MATH FUNCTIONS: Rel, Min/Max/Average/Std Dev/ Peak-to-Peak (of stored reading), Limit Test, %, and mX + b with user defined units dis-

played.

REMOTE INTERFACE:

Keithley XLinx Up & Running starter software
GPIB (IEEE-488.2) and RS-232C.
SCPI (Standard Commands for Programmable Instruments)
LabVIEW Drivers
TestPoint Drivers

ACCESSORIES SUPPLIED: Model 1751 Safety Test Leads, User Manual, Service Manual.

«
...
125
126
127
128
129
...
»

Содержание 2700















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2700

Бренд: Humandata Страницы: 30

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 42

Бренд: CTC Union Страницы: 56

Бренд: GB Страницы: 3

Бренд: GB Страницы: 3

Бренд: Fieldpiece Страницы: 2

Бренд: Maxwell Digital Multimeters Страницы: 13

Бренд: Maxwell Digital Multimeters Страницы: 16

Бренд: Picotest Страницы: 192

Бренд: TC Communications Страницы: 108

Бренд: Icel Manaus Страницы: 34

Бренд: Major tech Страницы: 12

Бренд: Keithley Страницы: 936

Бренд: Velleman Страницы: 9

Бренд: Benning Страницы: 184

Бренд: Surtek Страницы: 48

Бренд: UfiSpace Страницы: 31

Бренд: Kaiweets Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды