Keithley 2700 страница 143 Скачать руководство пользователя

Страница: 143 / 174

Calibration Reference

B-7

:DATE

(:CALibration:PROTected:DATE)

Purpose

To send the calibration date to the instrument.

Format

:cal:prot:date <year>, <month>, <day>

Parameter

<year> = 1999 to 2098
<month> = 1 to 12
<day> = 1 to 31

Query format

:cal:prot:date?

Response

Description

The

:DATE

command allows you to store the calibration date in instrument

memory for future reference. You can read back the date from the instru-
ment over the bus by using the

:DATE?

query or the CALIBRATION

selection in the front panel CAL menu.

NOTE

The year, month, and day parameters must be delimited by commas.

Example

:CAL:PROT:DATE 1999,12,16

Send cal date (12/16/1999).

:CAL:PROT:DATE?

Request cal date.

:NDUE

:CALibration:PROTected:NDUE)

Purpose

To send the next calibration due date to the instrument.

Format

:cal:prot:ndue <year>, <month>, <day>

Parameter

<year> = 1999 to 2098
<month> = 1 to 12
<day> = 1 to 31

Query format

:cal:prot:ndue?

Response

Description

The

:NDUE

command allows you to store the date when calibration is next

due in instrument memory. You can read back the next due date from the
instrument over the bus by using the

:NDUE?

query or the front panel CAL

menu.

NOTE

The next due date parameters must be delimited by commas.

Example

:CAL:PROT:NDUE 2000,12,16

Send due date (12/16/2000).

:CAL:PROT:NDUE?

Request due date.

Содержание 2700















































































































































































Результаты поиска

Содержание 2700

Отзывы:

Похожие инструкции для 2700

Бренды по названию

Популярные бренды

Keithley 2700, Руководство по обслуживанию

Результаты поиска

Содержание 2700

Отзывы:

Похожие инструкции для 2700

Бренды по названию

Популярные бренды