manualshive.com logo in svg

Keithley 2700, Руководство по обслуживанию

Поделиться
Скачать
Keithley 2700 Скачать руководство пользователя страница 71

Calibration

2-23

5.

Press SHIFT then TEST, then display TEST:CALIB with the up or down range key. 
Press ENTER, select RUN, then enter the appropriate calibration code (default: 
002700).

6.

Using the up or down range key, select CARD at the CAL:RUN prompt, then press 
ENTER.

7.

Set the display value to the cold calibration temperature (˚C) you measured in Step 3, 
then press ENTER to complete Model 7700 calibration.

Remote Model 7700 calibration

1.

Connect the Model 7700 to the 7797 Calibration/Extender Board (see “Extender board 
connections” above).

2.

With the power off, install the Model 7700/7797 combination in Slot 1, and select the 
rear inputs with the INPUTS switch. Allow three minutes for thermal equilibrium.

3.

Accurately measure and record the cold temperature of the Model 7700 card surface at 
the center of the card.

4.

Press in and hold the Model 2700 OPEN key while turning on the power.

5.

Enable calibration by sending the :CODE command. For example, the default com-
mand is:

:CAL:PROT:CODE 'KI002700'

6.

Initiate calibration by sending the following command:

:CAL:PROT:CARD1:INIT

7.

Calibrate the Model 7700 with the following command:

:CAL:PROT:CARD1:STEP0 <temp>

Here <temp> is the cold calibration temperature (˚C) measured in Step 3.

8.

Send the following commands to save calibration and lock out calibration:

:CAL:PROT:CARD1:SAVE

:CAL:PROT:CARD1:LOCK

Содержание 2700















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды