Keithley 2700 Скачать руководство пользователя страница 153

Страница: 153 / 174

Calibration Reference

B-17

:CODE

(:CALibration:PROTected:CODE)

Purpose

To program the calibration code or password so that you can perform the
Model 7700 calibration procedures.

Format

:cal:prot:code '<char_string>'

Parameter

Up to a 8-character string including letters and numbers.

Description

The

:CODE

command enables the Model 2700 calibration procedures

when performing these procedures over the bus. This command must be
sent to the unit before sending any other Model 7700 calibration command.
The default calibration code is KI002700.

NOTES

The

:CODE

command should be sent only once before performing calibration. Do

not send

:CODE

before each calibration step.

The code parameter must be enclosed in single quotes.

Example

:CAL:PROT:CODE 'KI002700'

Send default code of KI002700.

:COUNt?

(:CALibration:PROTected:CARD1:COUNt?)
(:CALibration:PROTected:CARD2:COUNt?)

Purpose

To determine how many times a Model 7700 has been calibrated.

Format

:cal:prot:card1:coun?

:cal:prot:card2:coun?

Response

<n> Calibration count.

Description

The

:CARD1:COUNt?

and

:CARD2:COUNt?

commands allow you to

determine how many times a Model 7700 in Slot 1 and Slot 2 respectively
has been calibrated.

NOTE

Use the

:COUNt?

command to help you monitor for unauthorized calibration

procedures.

Example

:CAL:PROT:CARD1:COUN?

Request card 1 calibration count.

Содержание 2700















































































































































































Результаты поиска

Содержание 2700

Отзывы:

Бренды по названию

Популярные бренды

Keithley 2700, Руководство по обслуживанию

Результаты поиска

Содержание 2700

Отзывы:

Бренды по названию

Популярные бренды