Keithley 2700 страница 128 Скачать руководство пользователя

Страница: 128 / 174

A-8

Specifications

Cold junction
Ref x3

Channel 1

Channel 10

(Channels 2–9)

Channel 11

Channel 20

(Channels 12–19)

Channel 21

Channel 22

AMPS

Sense

Input

Channel 23

2-Pole (Open)

4-Pole (Closed)

(see Note)

To Model 2700
Backplane

Channel 25

(see Note)

Backplane

isolation

Channel 24

(see Note)

Backplane

isolation

NOTE

Channels 23–25 in this schematic
refer to the designations used for
control and not actual available channels.

For more information, refer to the
ROUTe:MULTiple command section
in the Model 2700 User’s Manual.

Channels 24 and 25 can be individually
controlled using ROUTe:MULTiple if the
module is not to be connected to the
internal DMM.

Card

AMPS

Card Sense

Card Input

Cold junction
Ref x3

GENERAL

20 CHANNELS: 20 channels of 2-pole relay input. All channels config-

urable to 4-pole.

2 CHANNELS: 2 channels of current only input.

RELAY TYPE: Latching electromechanical.

ACTUATION TIME: <3ms.

CAPABILITIES

CHANNELS 1-20: Multiplex one of 20 2-pole or one of 10 4-pole signals

into DMM.

CHANNELS 21-22: Multiplex one of 2 2-pole current signals into

DMM.

INPUTS

MAXIMUM SIGNAL LEVEL:

Channels (1-20): 300V DC or rms, 1A switched, 60W, 125VA maxi-

mum.

Channels (21-22): 60V DC or 30V rms, 3A switched, 60W, 125VA

maximum.

CONTACT LIFE (typ): >10

operations at max signal level.

>10

operations cold switching.

CONTACT RESISTANCE: <1

Ω

at end of contact life.

CONTACT POTENTIAL: <±500nV typical per contact, 1µV max.

<±500nV typical per contact pair, 1µV max.

OFFSET CURRENT: <100pA.

CONNECTOR TYPE: Screw terminal, #20 AWG wire size.

ISOLATION BETWEEN ANY TWO TERMINALS: >10

Ω

, <100pF.

ISOLATION BETWEEN ANY TERMINAL AND EARTH: >10

Ω

, <200pF.

CROSS TALK (10MHz, 50

Ω

Load): <–40dB.

INSERTION LOSS (50

Ω

Source, 50

Ω

Load): <0.1dB below 1MHz.

<3dB below 2MHz.

COMMON MODE VOLTAGE: 300V between any terminal and chassis.

T/C COLD JUNCTION: 1.0°C (18°–28°C Mainframe Temp)

1.5°C (0°–18°C & 28°–50°C Mainframe Temp).

ENVIRONMENTAL:

OPERATING ENVIRONMENT: Specified for 0°C to 50°C.

Specified to 80% R.H. at 35°C.

STORAGE ENVIRONMENT: –25°C to 65°C.

WEIGHT: 0.45kg (1 lb).

7700 20-Channel Differential Multiplexer w/Automatic CJC

Содержание 2700















































































































































































Результаты поиска

Содержание 2700

Отзывы:

Похожие инструкции для 2700

Бренды по названию

Популярные бренды

Keithley 2700, Руководство по обслуживанию

Результаты поиска

Содержание 2700

Отзывы:

Похожие инструкции для 2700

Бренды по названию

Популярные бренды