JVC GY-HM180E, Инструкция по эксплуатации

Страница: 65 / 194

Memo :
0
When the [AUX] terminal is not connected,
[Main Menu]
B
[A/V Set]
B
[Audio Set]
B
[CH1
INT]/[CH2 INT] is fixed at “Int. Mic L”/“Int. Mic
R” respectively.
Setting Input Channel to [INPUT1]/[INPUT2]
Select the audio to input to [INPUT1] and [INPUT2]
terminals using the [AUDIO INPUT INPUT1]/
[AUDIO INPUT INPUT2] signal selection switch.
Setting Description
[LINE] Use this setting when connecting to
an audio device or other equipment.
The reference input level is +4 dBu.
[MIC] Use this setting when connecting to
a dynamic microphone.
[MIC+48V] Use this setting when connecting to
a microphone (phantom
microphone) that requires a +48 V
power supply.
Memo :
0
When “MIC” or “MIC+48V” is selected, set the
reference input level in [Main Menu]
B
[A/V
Set]
B
[Audio Set]
B
[Input1 Mic Ref.]/[Input2
Mic Ref.].
(
A
P113 [Input1 Mic Ref./Input2 Mic Ref.
O
] )
Caution :
0
When connecting a device that does not require
a +48 V power supply, make sure that it is not
set to the “MIC+48V” position.
0
When the [AUDIO INPUT INPUT1]/[AUDIO
INPUT INPUT2] signal selection switch is set to
“MIC”, make sure that a microphone is
connected to the [INPUT1]/[INPUT2] terminal. If
you increase the recording level when a
microphone is not connected, noise from the
input terminal may be recorded.
0
When a microphone is not connected to the
[INPUT1]/[INPUT2] terminal, set the [AUDIO
INPUT INPUT1]/[AUDIO INPUT INPUT2] signal
selection switch to “LINE” or adjust the volume
with the [CH-1]/[CH-2] recording level
adjustment knob.
Adjusting the Audio Recording Level
O
You can select to adjust the audio recording levels
for the two channels (CH1/CH2) manually or
automatically.
.
Manual Adjustment Mode (Manual
Adjustment)
0
Set the [AUDIO SELECT CH-1/CH-2 AUTO/
MANU] switch on the camera recorder to
“MANU” to enter the manual adjustment mode,
and use the [CH-1]/[CH-2] recording level
adjustment knob to set the recording level.
0 You can adjust the level manually during the
recording, recording standby, and stop modes.
Memo :
0
When the [FULL AUTO] button is set to “ON” and
[Main Menu]
B
[A/V Set]
B
[Audio Set]
B
[Audio
On FULL AUTO] is set to “Auto”, the [AUDIO
SELECT CH-1 AUTO/MANU] and [AUDIO
SELECT CH-2 AUTO/MANU] switches are
disabled.
(The above setting is the factory default.)
o
Setting Input Channel to “INPUT1”/
“INPUT2”
1
Set the [AUDIO SELECT CH-1/CH-2 AUTO/
MANU] switch to “MANU” for the channel to
be adjusted manually.
2
Turn the corresponding [CH-1]/[CH-2]
recording level adjustment knob to adjust
the level.
Adjust such that the audio level meter does not
light up at -2 dB even for loud sounds.
(
A
P113 [ Limiter Mode ] )
.
1/ 100
F1. 6
18 dB
AE
+
6
ND 1 /16
12 :34 : 56
Jan 24 , 2015
00: 00: 00.00
4030 20 10 0
5 . 6f t
P 15000K
4030 20 10 0
-2dB
66
Audio Recording
Sh
ooting