JVC GY-HM180E, Инструкция по эксплуатации

Страница: 113 / 194

Memo :
0
You can select either “Link” or “Separate” only
when the [CH-1/CH-2] audio input signal
selection switch is set to “INPUT1”/“INPUT2”
respectively and both the [AUDIO INPUT
INPUT1/INPUT2] input signal selection
switches are set to the same setting and both the
[AUDIO SELECT CH-1/CH-2 AUTO/MANU]
switches are set to “AUTO”.
0
This item is fixed at “Link” when [CH1 INT] and
[CH2 INT] have the following combinations.
0
“AUX L” and “AUX R”
0
“Int. Mic L” and “Int. Mic R”
0
In all other cases, it is fixed at “Separate”.
9 CH1 Limiter/CH2 Limiter
For specifying the limiter settings for the CH1/CH2
audio input.
o
Threshold Level
For setting the value for activating the limiter.
[Setting Values: -9dBFS,
R
-6dBFS, Off]
o
Attack Time
For setting the response speed for activating the
limiter.
[Setting Values: Fast,
R
Middle, Slow]
o
Decay Time
For setting the attenuation rate after the limiter
is activated.
[Setting Values: Fast,
R
Middle, Slow]
Memo :
0
When [Limiter Mode] is set to “Link”, [CH2
Limiter] cannot be specified.
0
If the channel specified is set to “AUTO”,
[Threshold Level] cannot be set to “Off”.
INPUT1 Mic Wind Cut/INPUT2 Mic Wind Cut
O
For selecting whether to cut the low frequencies of
the audio input signals (low-cut) when the [AUDIO
INPUT INPUT1]/[AUDIO INPUT INPUT2] selection
switch is set to “MIC” or “MIC+48V”.
Set this item to reduce wind noise from the
microphone.
[Setting Values: On
,
R
Off]
Memo :
0
This item is not displayed if the handle unit is not
connected.
Int. Mic Wind Cut
For selecting whether to cut the low frequencies of
the audio input signals (low-cut) from the built-in
microphone. Set this item to “On” to reduce wind
noise from the microphone.
[Setting Values: On
,
R
Off]
Memo :
0
This item is enabled in the following cases.
0
When the [CH-1] or [CH-2] selection switch is
set to “INT”.
O
0
[CH1 INT] is set to “Int. Mic L” or [CH2 INT] is
set to “Int. Mic R”.
(
A
P112 [ CH1 INT ] )
(
A
P113 [ CH2 INT ] )
Int. Mic Stereo Enhancer
For setting the enhancement level of the stereo
effect of the built-in microphone.
0
On :
Enhances the stereo effect.
0
Off:
Does not enhance the stereo effect.
[Setting Values:
R
On , Off]
Memo :
0
This item is enabled in the following cases.
0
Both [CH-1] and [CH-2] selection switches
are set to “INT”.
O
0
[CH1 INT] is set to “Int. Mic L” and [CH2
INT] is set to “Int. Mic R”.
(
A
P112 [ CH1 INT ] )
(
A
P113 [ CH2 INT ] )
Monitor
For setting the audio output from the [
x
] jack or the
speaker.
0
Stereo:
Outputs audio from [CH1] to L and audio from
[CH2] to R.
0
Mix:
Generates a mixed audio output from [CH1] and
[CH2].
0
CH1:
Outputs only the audio input from [CH1].
0
CH2:
Outputs only the audio input from [CH2].
[Setting Values:
R
Stereo, Mix, CH1, CH2]
114
A/V Set Menu
Menu
Display and
D
etailed
S
etti
ngs