Jungheinrich DFG 316s страница 85 Скачать руководство пользователя

Страница: 85 / 187

05.10 EN

NOTE

Loads must not be deposited on travel or escape routes, in front of safety
mechanisms or operating equipment that must be accessible at all times.

Transporting load units

Requirements

– Load unit correctly lifted.
– Load handler lowered for transport (approx. 150 - 200 mm above the ground).
– Mast tilted back fully.

Procedure

• Accelerate and decelerate gradually.
• Adapt your travel speed to the conditions of the route and the load you are

transporting.

• Watch out for other traffic at crossings and passageways.
• Always travel with a lookout at blind spots.
• On slopes and inclines always carry the load facing uphill, never approach at an

angle or turn.

Depositing load units

Requirements

– Warehouse location suitable for storing the load.

Procedure

• Set the mast vertical.
• Drive carefully up to the storage location.
• Carefully lower the load handler so that the forks are clear of the load.

Avoid depositing the load to avoid damaging the load and the load handler.

• Lower the load handler.
• Carefully remove the forks from the pallet.

The load unit is lowered.

Содержание DFG 316s




























































































































































































Результаты поиска

Содержание DFG 316s

Отзывы:

Похожие инструкции для DFG 316s

Бренды по названию

Популярные бренды

Jungheinrich DFG 316s, Руководство по эксплуатации

Результаты поиска

Содержание DFG 316s

Отзывы:

Похожие инструкции для DFG 316s

Бренды по названию

Популярные бренды