manualshive.com logo in svg

JR XP6102, Инструкция по эксплуатации

Поделиться
Скачать
JR XP6102 Скачать руководство пользователя страница 48

www.modelflight.com.au

 – World’s best source of JR products 

 

 

7E 

CONTROL STICK LENGTH ADJUSTMENT  

 

To adjust the stick length, use the

 

2mm Allen wrench (supplied with your 
XP6102 transmitter) to unlock the set 
screw. Turn the wrench counterclockwise 
to loosen the screw. Then, turn the

 

stick clockwise to shorten or 
counterclockwise to lengthen. After the 
control stick length has been adjusted 
to suit your flying style, tighten the

 

2mm set screw. If you desire longer 
sticks, JR

®  

offers a stick (JRPA047) that

 

is approximately one inch longer than 
standard. This stick, crafted from bar 
stock aluminum, is available at your 
local JR dealer.

 

 

SET SCREW

 

 

 

 

 

 

LOOSEN

 

 

 

TIGHTEN

 

7F 

CONTROL STICK TENSION ADJUSTMENT  

 

Remove the Ni-Cd battery and six 
transmitter back screws as shown on the 
previous page. Remove the transmitter 
back, being careful not to cause damage 
to any components.

 

Adjust each screw for desired tension

 

(counter-clockwise to loosen stick feel; 
clockwise to tighten stick feel). When 
adjusting the throttle ratchet tension, 
make sure that the adjusting screw 
does not touch the PC board after 
adjustment is complete.

 

7G 

DIRECT SERVO CONTROL (DSC)  

 

For proper DSC hook-up and 
operation:

 

1. Leave the transmitter power switch 

in the Off position. The transmitter 
will not transmit any radio frequency

 

(RF) in this position.

 

2. Plug the (supplied) DSC cord into the

 

DSC port in the rear of the transmitter.

3. The encoder section of the transmitter 

will now be operational and the LCD 
display will be lit.

 

4. Plug the other end of the DSC Cord 

into the receiver charge receptacle. 
Turn the switch harness to the On 
position.

 

Note

: When you install the charging 

jack, be sure to hook the charging 
jack receptacle securely into the 
switch harness charge cord.

 

 

Why you should use the DSC

 

function:

 

1. The DSC enables you to check the 

control surfaces of your aircraft without 
drawing the fully operational 200mAh 
from your transmitter battery pack. 
Instead, you will only draw

 

approximately 70mAh when using the

 

DSC function.

 

2. The DSC function allows you to make 

final adjustments to your airplane 
without transmitting any radio signals. 
Therefore, if another pilot is flying on 
your frequency, you can still adjust your 
aircraft and not interfere with the other 
pilot’s aircraft.

 

Note

: This function is for bench- 

checking your helicopter only.

 

 

 

 

 

A—Charge Cord/DSC Receptacle 
B—Switch Harness Lead C—
Charger/DSC Cord

 

 

 

 

 

 

 

B

 

A

 

 

 

 

 

C

48 

XP6102 - Helicopter Manual

 

Содержание XP6102



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды