JR X9503 2.4 Скачать руководство пользователя страница 97

Страница: 97 / 107

Step #23 Cruise Pre-sets

Step #24 Dual Rate and Exponential

Step #25 Elevator-to-Flap Mix

S-56

S-57

FUNC.LIST

, highlight D/R & EXP. Press the

Selector

to access the Dual Rate and Exponential menu. Highlight

the channel (aile, elev or rudd) then press the

Selector

select the desired channel you wish to adjust the dual and

expo rates for. Rotate to select then press the

Selector

store the desired channel.

Note

: Three D/R and EXPO positions (values) are

available (Pos0, 1 and 2).

Under

AUTO

on the right of the screen, highlight

CRUI

and press the

Selector

. Select

Pos1

as the

active position for the cruise mode by rotating the

Selector

then pressing it when

Pos1

is highlighted.

This will automatically access dual rate and expo values

programmed into position 1 whenever cruise mode

is selected. Now rotate the

Selector

Pos1

and

highlight the D/R values. Rotate the

Selector

change

these values. Displace the aileron stick right or left to

independently adjust the dual rate in each direction.

Depress the

Selector

to store the desired D/R values.

Rotate the

Selector

to the

EXP Pos1

values and adjust

these values in the same manner, pressing the

Selector

to store the desired value.

Now go back to channel and repeat for the two remaining

channels. Press the

LIST

button to return to the Function

Mode screen.

This function is normally not used in cruise mode;

however, it is active and all trim adjustments will be

automatically stored when cruise mode is selected.

Function Mode

list, highlight

ELE



FLP M

. Press

the

Selector

to access the Elevator-to-Flap mix menu.

Note that two elevator-to-flap mix values are available,

Pos0 and Pos1, and the elevator-to-flap values can be

independently adjusted up and down. Also, you can adjust

the offset (the stick position where the mixing changes

from up to down). This offset allows the programming

of snap-flaps, a common sailplane function that gives

greater full up elevator pitch authority for tighter turns.

With snap-flaps, no flap mixing occurs during small to

medium up elevator inputs, but at about 80% up elevator,

the flaps are mixed to give down flaps, causing greater up

pitch authority.

Highlight

CRU

(cruise mode) at the bottom of the screen

and depress the

Selector

to select Pos1. If you choose to

program snap-flaps, highlight Offset Pos1 and depress the

Selector

to access this value. A 0 value locates the offset

position when the elevator is centered. The adjustment

range is -200 to +200. Negative values move the offset

in the up elevator direction. Set a value of –100 to start,

as this will locate the offset at 80% up elevator. Press the

Selector

to store this offset value. Highlight Pos1 UP and

depress the

Selector

to access the position 1 up elevator

mixing. With the 3-position switch in the middle (cruise)

position, give a full up elevator command and hold while

adjusting the Pos1 up value until the desired down flap

position is achieved. Press the

LIST

button to return to

the Function Mode screen.

Содержание X9503 2.4












































































































Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды

JR X9503 2.4, Инструкция и руководство по программированию

Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды