JR X9503 2.4 Скачать руководство пользователя страница 100

Страница: 100 / 107

Step #31 Land Presets

Step #32 Dual Rate and Exponential

S-62

S-63

The X9503 2.4 offers a sophisticated program with easy

preset trim positions for the elevator, flaps, flaperons

(and even the aileron and rudder if you choose). The

system can remain active in flight allowing you to fine-

trim presets in each flight mode or can be locked in so

they cannot be altered in flight. Flight mode presets are

automatically selected via the flight mode switch and are

adjusted with the digital elevator trim, the digital flap trim

and the digital auxiliary trim (flaperon). While the presets

are adjusted via the digital trims, their positions are

recorded in the servo monitor.

To access the servo monitor, in

FUNC.LIST

highlight

MONITOR

. Press the

Selector

to access the Monitor

menu then press the

Selector

again to access the camber

digital preset screen. To adjust the presets, move the

flight mode switch to the land mode (down) position.

Adjust the preset positions via the flap trim, auxiliary

trim and elevator trim on the transmitter. The values will

will display in the screen and then will be memorized for

that flight mode. If you want these preset values to be

fixed (not active in flight) once the values are established,

return to the Trim Step screen in the system mode and

reduce the value of the desired channel to 0. The preset

values for all flight modes will be stored and no longer

accessible with the digital trims.

FUNC.LIST

, highlight

D/R & EXP

. Press the

Selector

to access the Dual Rate and Exponential menu. Highlight

the channel (aile, elev or rudd) then press the

Selector

to select the channel you wish to adjust the dual and expo

rates for. Rotate to select then press the

Selector

to store

the desired channel.

Note that three D/R and EXPO positions (values) are

available (Pos0, 1 and 2).

Under

AUTO

on the right of the screen, highlight

LAND

and press the

Selector

. Select

POS2

as the active

position for land mode by rotating the

Selector

and

pressing the

Selector

when

POS2

is highlighted. This

automatically accesses dual rate and expo values that

are programmed into position 2 whenever land mode is

selected. Now rotate the

Selector

POS2

and depress

to highlight the D/R values. Rotate the

Selector

change these values. Displace the aileron stick right or

left to independently adjust the dual rate in each direction.

Depress the

Selector

to store the desired D/R values.

Rotate the

Selector

to the

EXP Pos2

values and adjust

these values in the same manner. Press the

Selector

store the desired value.

Now go back to channel and repeat for the two remaining

channels. Press the

LIST

button to return to the Function

Mode screen.

Содержание X9503 2.4












































































































Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды

JR X9503 2.4, Инструкция и руководство по программированию

Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды