JR X9503 2.4 Скачать руководство пользователя страница 50

Страница: 50 / 107

ACTIVATE/DEACTIVATE SWITCHES

GOVERNOR PROGRAM ACTIVATION

SWASH TYP-SWASHPLATE TYPE

Accessing the Swashplate Type Function

H-12

H-13

The X9503 2.4 provides the ability to disable a number of

the switches on the transmitter – Pit TRIM, GEAR, AUX2,

AUX3, and AUX4. This is very useful when using auxiliary

channels for special or mixing purposes. In this instance,

the auxiliary channels are no longer to be operated

by their auxiliary switches but rather the program mix

selected or transmitter sticks. Such as when the selected

program mix or transmitter sticks operate the auxiliary

channels, instead of the auxiliary switches.

1. If using PIT TRIM, GEAR, AUX2, AUX3, or AUX4 as a

2nd primary flight control, inhibit the corresponding

switch by highlighting ACT, along the bottom line

of the display and pressing the

Selector

until INH

appears under the switches to be turned off. The

example below shows all switches as INH or turned

off, making them all available as a 2nd channel for a

primary flight control.

The X9503 2.4 features a special Governor program you

can activate in the Device Select screen.

You can use the Governor program with the most

current Governor systems. The program also allows for

independent rpm settings for each of the active flight

modes.

1. From within the

Devic.SEL

function use the

Selector

to highlight and select

OUT:ACT

located at the bottom of

the

GEAR

column along the bottom line of the display.

2. Press the

Selector

until the word

GOV

appears on

the display. This indicates the Governor function is

activated. The Governor program is now visible in the

Function Mode List.

1. While pressing the

ENT

key, switch the transmitter ON

to enter system mode.

2. Roll the

Rolling Selector

until

SWASH TYP

is highlighted, then press the

Selector

to access.

3. Press the

Rolling Selector

again, and the screen will

display the available swashplate types. Highlight the

desired swashplate type, then press the

Selector

select.

4. Pressing the

CLR

key will reset the Swashplate Type to

the factory default (Normal) position.

5. To exit the Swashplate Type function, roll the

Rolling

Selector

to highlight

LIST

, and press.

This concludes the SYSTEM Menu portion of the Heli

Mode. Continue with FUNCTION LIST below to complete

the Heli setup.

The Swashplate Mixing function enables the X9503 2.4

system to operate many different types of swashplate

control systems, including 5 different versions of CCPM.

The Swashplate options are:

1 Servo

Non-CCPM, standard mixing type

2 Servo/180° CCPM

3 Servo/120° CCPM (JR style, most popular)

3 Servo/140° CCPM (JR Vigor

™

CS, JR Vibe

™

90)

3 Servo/90° CCPM

4 Servo/90° CCPM

Содержание X9503 2.4












































































































Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды

JR X9503 2.4, Инструкция и руководство по программированию

Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды