JR X9503 2.4 Скачать руководство пользователя страница 96

Страница: 96 / 107

Step #21 Flap Rate, Camber Mix and Camber Adjust (continued)

Step #22- Aileron-to-Rudder Mix

S-54

S-55

Flaperon Mix

Note

: Flap rate must be set before camber mix.

FUNC.LIST

highlight

Flaprn MX

. Press the

Selector

to access the Camber Mix menu. Highlight the launch

FPRN down value then press the

Selector

to access

this value. With the flight mode switch in the upper

launch mode, move the left side lever to the lowermost

position and adjust the down value to the desired flaperon

Flaperon Mix Delay

The camber adjust menu allows the programming of a

delay from 0 to 2 seconds. This delay affects the flap,

flaperon and elevator presets when switching from one

flight mode to another. When inhibited, no delay occurs

and the servo immediately transitions from one preset trim

position to another when the flight modes are switched.

With a delay programmed the transition is smooth relative

to the delay time. A break-off function is available that you

can program to override the delay, based on a selected

elevator stick position. For this setup, we will program a

1.0 second delay for Launch.

position. Press the

Selector

to store the value. Now with

the flight mode switch in the upper launch mode, move

the left side lever to the uppermost position and adjust

the up value to the desired flaperon position and store

by pressing the

Selector

. Repeat the process for the up

and down elevator camber mix. Press the

LIST

button to

return to the Function Mode screen.

FUNC.LIST

highlight

FM Delay

. Press the

Selector

to access the Camber Adjust menu. Highlight the launch

delay value then press the

Selector

to access this value.

Rotate the

Selector

to adjust the value to 1.0s (seconds),

Press the

Selector

to store the value. Press the

LIST

button to return to the Function Mode screen.

FUNC.LIST

highlight

AIL



RUD M

. Press the

Selector

to access the Aileron-to-Rudder mix menu.

Highlight the launch left value then press the

Selector

access that value. With the flight mode switch in the upper

launch mode, give a full left aileron command and rotate

the

Selector

to achieve the desired left rudder throw.

Press the

Selector

to store the value. Now highlight the

launch right value and adjust it to the desired position.

Press the

LIST

button to return to the Function Mode

screen.

Setting Up Cruise Mode

In Step #8, Establishing Flight Modes, flight modes were

programmed to operate from the left front 3-position

switch. To select Cruise mode, move the left 3-position

switch to the middle position. In the main (info) screen

CRUISE

appears in the upper portion of the display when

Cruise mode is selected. When making programming

changes/adjustments in Cruise mode, this 3-position

switch must remain in the middle position during the

process to allow the results of those adjustments to be

seen on the model.

Содержание X9503 2.4












































































































Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды

JR X9503 2.4, Инструкция и руководство по программированию

Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды