JR X9503 2.4 Скачать руководство пользователя страница 45

Страница: 45 / 107

Copy – Copying the Currently Selected Model to Another Model Memory

ACCESS THE SYSTEM MENU

Model SEL- Model Selection

H-2

H-3

The Copy function is part of the Model SEL function

and allows you to copy the current model memory into

another model memory in the same transmitter. It is not

used to transfer the model to another transmitter or to a

Data Safe unit – the DATA TRANSFER function provides

for these activities.

The Copy function can provide some insurance against

losing programs (helicopter setups) that may have

been very time-consuming to create. You should use

the Copy function to make a backup copy of the model

memory after you have completed, tested and refined the

programming.

Making a backup copy protects you from losing the

original program while allowing you to experiment with

the original program. You can restore the original settings

by copying the backup copy back to the original model

memory.

1. Select the model to copy – see Model SEL description

at the beginning of the HELI section.

2. Highlight and select Model SEL in the SYSTEM Menu.

Highlight and select Select to obtain the Copy display.

The display shows the currently selected model on top

with a down arrow pointing to the lower model memory

that the current model will be copied into. The data in

the lower model memory will be entirely replaced by the

data in the currently selected model, so be sure the lower

model is either empty or contains data no longer required.

To set up a new model, first select the desired model.

Generally, an unused model memory is selected.

However, you can use a model containing data for another

model, as long as you no longer need the data, as any

information in that memory will be lost.

1. Bring up the

SYSTEM Menu

by holding down the

ENT

button while turning the transmitter on.

1. In the

SYSTEM Menu

, highlight and select

Model

SEL

using the

Selector

2. Use the

Selector

to highlight and select the desired

model number.

3. Return to the SYSTEM Menu by pressing the

LIST

button.

Содержание X9503 2.4












































































































Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды

JR X9503 2.4, Инструкция и руководство по программированию

Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды