JR X9503 2.4 Скачать руководство пользователя страница 60

Страница: 60 / 107

GOVERNOR- GOVERNOR FUNCTION

PROG MIX 1-6 – PROGRAMMABLE MIXES 1 through 6

H-32

H-33

Note

: The GOVERNOR function is only listed in

Function Mode when first activated in the Device

Select function in System Mode.

You can use the X9503 2.4’s Governor function with most

currently available Governors. The Governor function

allows you to set the Governor rpm values for each of

the Active Flight modes. It automatically changes the

Governor rpm values as set when the Flight Mode switch

is moved through each of the active flight modes.

The value range in the Governor function is +/-

0%–125%, and its values follow the Travel Adjust values

exactly. In other words, a desired Travel Adjust value of

+55% is +55% in the Governor function.

The Governor program, when activated in System Mode,

functions through the GEAR channel (Channel 5) of the

X9503 2.4. To properly connect a Governor to the receiver,

connect the rpm signal lead from the Governor to the Gear

(CH5).

Accessing the Governor Function

1. Turn the transmitter ON.
2. Press the

LIST

key to enter

Function mode

3. Highlight the

GOVERNOR

function. Press the

Selector

to access.

4. Highlight the value to be adjusted with the

Selector,

then press to access the value. Roll the

Selector

adjust the value as needed.

5. To exit the Governor function, highlight

LIST

, and

press.

Note

: Flight Modes ST-3 and ST-4 will only be

shown if activated previously in

System Mode.

For Governors like the Model Avionics “Throttle Jockey,”

leave the Travel Adjust values for the Gear channel at

+/-100%, and set your Governor rpm values from the rpm

calculator in the Governor function.

For other brand Governors, you should also leave

the Travel Adjust values for the Gear Channel (CH5)

at +/-100%. You can then increase the values in the

Governor function above +/-100% up to +/-125% to

increase the rpm remotely from the preset rpm selected at

the Governor.

Note

: To turn off the Governor Function for engine

tuning, etc. return the value for the desired flight

mode to zero. Remember the value so it can be

re-entered after tuning.

The X9503 2.4 System provides 4 Standard

programmable mixes (PROG.MIX3 through PROG.MIX6)

and 2 Multi-Point programmable mixes (PROG.MIX1 &

PROG.MIX2). Mixing occurs when the pilot moves a stick,

switch or lever on the Master channel and the transmitter

generates an input for the Slave channel. The Slave’s input

is based on the pilot’s input to the Master channel and the

parameter defined in the programmable mixer.

You can use programmable mixers whenever you want

a channel to react or move (Slave) by providing input

to another channel (Master), or to move a channel by

moving a switch or lever. They are typically used to

compensate for deficiencies in helicopter design/setup

such as eliminating a pitch-to-aileron, or pitch-to-elevator

trim change issue when collective is given. They are also

used to activate special helicopter functions like Retracts,

Landing Lights, etc.

Multi-Point Mixing provides the ability to define a

customized “curve” of travel that the Slave channel

follows as it reacts to the Master channel. It is different

from Normal Mixing in the sense that Normal Mixing

results in a linear movement of the Slave channel in

relation to the Master. With Multi-Point Mixing there

are 7 points (includes endpoints) along the travel of the

Master channel you can adjust to control the action of the

Slave channel (more or less travel in the same/opposite

direction) providing the ability to deviate from a linear

mixing action.

Mixes are programmable, allowing any of the 9 channels

to be Master, Slave or both. Additionally there are 4

options for Master channels that begin with a “#” (pound

sign), these Master channels are origin type mixes. These

include #AIL, #ELE, #RUD, and #PIT. Origin mixing

bypasses any other mixing that might affect that channel

such as throttle curves or other programming and uses

the stick position only to control the mix. There are also

4 options for Master channels that end with a + sign,

these Master channels are for type mixes. These include

THR+, ELE+, AIL+, and RUD+, and the trim of the Master

channel as well as any other mixing to the Master channel

to control the Slave channel of the mix. You can also set

the Timer, TIMT, switch (momentary switch) as the Master

channel of a mix.

You can also program the mixing parameters and include

the direction of travel of the Slave channel; the amount

of travel for the Slave channel; the Offset (where the mix

starts and changes direction) and the switches/levers/

sticks used to turn a mixer on and off. You can select and

adjust all of these elements in Programmable Mixes.

Some examples of how programmable mixers might be

used include but are certainly not limited to:

•

Swashplate Timing: Improves Rolling and

Vertical Maneuver tracking

Use this when a heli will not roll on its axis (tail boom)

correctly, or pulls to the Left or Right during pitching

maneuvers (loops, stall turns, etc.).

Most Helis need and can benefit from this form of mix to

improve their overall flight performance. This trick mixing

is used by most of the pros to make their models fly more

accurately, and in turn, more easily.

2 Separate Mixes are required

Mix 1: Elevator to Aileron (Corrects vertical

tracking)

Use a program mix Elevator to Aileron to correct a

Vertical pull/ issue. The mix allows the Aileron servo to

move slightly in the opposite direction of the out of track

direction in order to keep the aircraft from pulling left or

right when performing a vertical maneuver. This standard

mixer designates the Elevator as Master and the Ailerons

as Slave.

Mix 2: Aileron to Elevator (Corrects Rolling

Maneuvers)

To add swashplate timing for Rolling maneuvers, a similar

mix of Aileron (Master) to Elevator (Slave) would be

created additionally. For these types of mixes, you would

use Standard Program Mix numbers 3 through 6.

Содержание X9503 2.4












































































































Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды

JR X9503 2.4, Инструкция и руководство по программированию

Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды