JR X9503 2.4 Скачать руководство пользователя страница 40

Страница: 40 / 107

COPY – COPY CURRENT MODEL (continued)

TRANSFER – TRANSFER THE MODEL TO ANOTHER TRANSMITTER

RECEIVE A MODEL INTO THE X9503 2.4 – (Transfer function)

A-50

A-51

2. Highlight and select

Model SEL

in the

SYSTEM Menu

. Then highlight and select

Select

to obtain the Copy display.

3. Verify that the top model is the model you want to

back-up and the lower model is empty or no longer

required. When satisfied that all is correct, press the

CLR button on the left side of the display next to

COPY. The entire contents of the currently selected

model copy to the lower model on the display making

a complete backup of the current model. The upper and

lower model memory names are now the same since

the two model memories are identical.

You can use the backup copy to restore the original any

time. To do this, perform the Copy function reversing

the order of models copying the backup to the original

(backup copy on the top line and the original model

memory on the bottom line).

Note

: Since the X9503 2.4 has the ModelMatch

feature, to operate the receiver on a new model

number, you must first re-bind the receiver to the

new model for it to function.

The display shows the currently selected model on top

with a down-arrow pointing to the lower model memory

that the current model will be copied into. The data

presently in the lower model memory will be entirely

replaced by the data in the currently selected model, so be

sure the lower model memory is either empty or contains

data no longer required.

To change the lower model memory that will receive

the copy of the current model

highlight and select the

lower model name and number. Scroll to an unused

model memory or a memory that contains data no longer

required, and select it.

1. Hold the ENT button while plugging the trainer cord

into the back of the transmitter to obtain the

SYSTEM Menu

Plug the other end of the trainer cord into another X9503

2.4 transmitter while holding the

ENT

button down and

prepare that transmitter to Receive (described below).

2. Highlight and select

TRANSFER

in the

SYSTEM

Menu

to obtain the Transfer display.

The

TRANSFER

function is in the

SYSTEM Menu

and can copy the contents of a model memory to another

X9503 2.4 transmitter. It is also used to receive data for a

model, from another X9503 2.4 transmitter.

3. The model you will transfer must be the currently

selected model. If the model to be transferred is not

currently selected, see

Model SEL

in the

SYSTEM

Menu

to select the model.

4. When the receiving device is ready, press the

CLR

button next to

START

on the left side of the display.

The data for the currently selected model transfers to

the receiving device.

Содержание X9503 2.4












































































































Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды

JR X9503 2.4, Инструкция и руководство по программированию

Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды