JR X9503 2.4 Скачать руководство пользователя страница 37

Страница: 37 / 107

MULTI-POINT MIXER – Ex: ELIMINATE PITCH-COUPLING (continued)

TRAINER – TRAINER SYSTEM

X9503 USED AS MASTER (INSTRUCTOR) – (Trainer System)

A-44

A-45

Set Points for Travel and Direction

. There are

7 points along the travel of the Rudder (the line

intersected by the vertical line that moves right and

left with the Rudder stick). At each point an Elevator

deflection may be defined. A point that is set to 0%

represents no Elevator deflection at that point. A

negative value at a point typically indicates Up Elevator

movement while a positive value results in Down

Elevator movement. A point set to INH takes on the

value of the curve/line between the 2 adjacent points.

The direction of travel may be reversed (Up Elevator vs.

Down Elevator) by changing values from negative (-) to

positive (+) (moving the point values above and below

the 0% line).

Since the aircraft pitches to the landing gear with the

application of both Right and Left Rudder, the Elevator

deflection will be zero at center (Point-3) (no mixing).

At the points either side of Point-3 will be negative,

indicating Up Elevator movement. The more negative

a point value, the more Up Elevator deflection. Set the

points initially to the following values.

Point-0

- 10% (At full Right Rudder the Elevator will deflect

Up 10%)

Point-1

INH (Takes on the value along the curve between

Point-0 & Point-2)

Point-2

-3% (Elevator deflects Up 3% when Rudder is

moved to Point-2)

Point-3

0% (no Mixing – no Elevator deflection when

Rudder is at neutral)

Point-4

-3% (Elevator deflects Up 3% when Rudder is

moved to Point-4)

Point-5

INH (Takes on the value along the curve between

Point-4 & Point-6)

Point-6

-10% (At full Left Rudder the Elevator will deflect

Up 10%)

Offset

. Point-3 represents the offset position and

corresponds to the Rudder stick being at neutral. It is

important to leave Point-3 set at 0% to make sure there

is no mixing and therefore no Elevator deflection when

the Rudder is at neutral.

Verify Operation

. Turn the Receiver on and turn the

mix on using the Gear switch. Move the Rudder stick

from full right to full left. The Elevator should deflect

Up when the Rudder is moved in both directions. If

it moves down instead, change the percentages to

(+) values instead of (-) values at each point. If the

Elevator appears to be moving too much, reduce the

point values (less negative). If the Elevator does not

seem to move enough, then increase the point values

(more negative). Now turn the Gear switch to the OFF

position and verify that the Elevator does not move.

While test flying the aircraft, make note of the mixing and

whether it generates enough up-Elevator during knife-

edge to stop it from pitching to the gear, or generating

too much Elevator input, causing it to pitch to the canopy

instead of the gear. Also note the approximate position of

the Rudder stick when pitching occurs. Land the aircraft

and adjust the points closest to the position of the Rudder

stick when pitching occurs for more or less Elevator

deflection until the aircraft no longer pitches during knife-

edge. More negative generates more Up Elevator and less

negative generates less Up Elevator. Points 1 and 5 may

be activated and their value changed if necessary to fine-

tune the mix.

Note: To completely disable or otherwise

inhibit a mixer, highlight either the Master or

Slave and press the CLR button.

The X9503 2.4 contains a Trainer System that allows

the instructor to transfer some or all of the primary

flight control functions (Throttle, Aileron, Elevator and

Rudder) to the student. It also allows you to indicate if the

transmitter is the Master (controlled by the instructor) or

Slave (controlled by the student). The Snap Roll button

transfers control to the student when the X9503 2.4 is

being used as the Master/Instructor transmitter.

All Dual rates and Exponential settings in the Master

transmitter are transferred to the Slave transmitter when

the master transmitter channels are selected individually

in the trainer menu. The Slave transmitter battery must be

charged.

1. Connect the Trainer cord between the Master and

Slave transmitters. Turn the power on to the Master

transmitter. (The Slave transmitter remains powered off

and can even have the module removed if equipped

with a module)

2. Make sure the Slave transmitter is in the PPM/FM

modulation mode. If the slave system is a X9503 2.4,

or any other system that is Spread Spectrum only, such

as other JR 2.4GHz or Spektrum systems, this does not

apply.

3. Highlight and select

Trainer

in the

FUNC.LIST

obtain the Trainer Display.

1. If the X9503 2.4 is the Master transmitter select the

channel(s) operated by the Slave transmitter when the

trainer switch is depressed.

When all channel selectors are in the

MAST

position,

NORMAL

appears on the display and all 4 channels

are transferred to the student when the trainer switch is

depressed. When all channel selectors are in the MAST

position, the slave system must be programmed for the

model, meaning all programming necessary for the model

must be programmed in both the master and the slave

systems. Also when all the channel selectors are in the

MAST position, the slave system should be left in normal

default MASTER mode.

To transfer only certain channels to the student, highlight

and select the channels you will transfer, moving the

indicator for these channels to the

SLAV

position for

these channels. When less than all channels are selected

SLAV

PROGRAM T

appears on the display

indicating that the Trainer System has been programmed

to transfer only selected channels. When the channel

selectors are in the SLAV position, all programming of the

master system will be used, and only the stick movements

of the 4 primary channels are used from the slave system

when control is given to the slave transmitter. In this case,

the slave system does not need to be programmed for the

model. Also the slave system should be set to Slave mode

in it’s trainer system.

The X9503 2.4 is now ready to be used as the Master

or instructor transmitter. Depress the Snap Roll button

to transfer control to the student. Control will remain

transferred until the Snap Roll button is released.

Содержание X9503 2.4












































































































Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды

JR X9503 2.4, Инструкция и руководство по программированию

Результаты поиска

Содержание X9503 2.4

Отзывы:

Похожие инструкции для X9503 2.4

Бренды по названию

Популярные бренды