Joyello JL-1048 SECURFIX BEEP, Руководство пользователя

Страница: 24 / 68

24
GB
ADJUSTING THE HARNESS
8.Adjust the backrest angle
Installed forward-facing or rearward facing, there are 3 recline positions available.
Pull the positioning handle under the front of the seat upwards,and then pull or push
the seat forwards or backwards.Release the positioning handle in the desired
position and push until you hear “click”.
Check to make sure the child seat is securely locked in the desired
position by pulling the positioning handle.
Important:
9.Adjust the shoulder strap height
If the height of your shoulder belts in child car seat is not fit for your
child
,
adjust the height of the shoulder belt
,
Please proceed as follows
:
Step 1
.
Loosen the shoulder harness
(
see point 7.1
)
turn the child seat
to the back
.
Slide the chest straps
and shoulder straps off the harness
connectors.
Step 2. Pull the straps through the
shoulder strap slots from the front
of the child seat.Now you can remove
the shoulder straps and chest pad.
3
2
1
1
2
3
forward facing rearward facing
CLICK
6.Usage of buckle
Firstly
,
adjust the shoulder straps height
,
please proceed as follows
:
Step1
.
Put the two metal sections of the buckle connector together
.
Step2
.
Slot the two buckle connectors into the slot in the buckle until they
click place.
Step3
.
Check the harness is correctly locked by pulling the shoulder straps
upwards
.
To release the harness
,
you can press the red button of the buckle downwards
,
the two metal sections will be pop up .
“ ”
7.Adjust and use the harness
7.1 Loosen the harness
The harness is slackened by pressing the adjuster
(under the adjuster cover)on the front of the seat.
Press down the adjuster as you grip
the two shoulder
straps with your another hand.Pull the shoulder
straps towards you to loosen the harness.
7.2 Tighten the harness
Pull the shoulder straps upwards to remove the slack
from the lap sections of the harness then pull the
adjuster strap until the harness is fully tightened.
The harness should be adjusted as tightly as possible
without causing discomfort to your child.
A loose harness can be dangerous.Check the harness
adjuster and tighten each time the child is placed in
the seat.
CLICK
PRESS
Step 3. Then re-thread the shoulder
straps and chest straps into the
appropriate strap slots from the front
of the child seat and slide them in the
harness connectors.
Make sure that both of the
shoulder belts and chest belt go through
slots at the same height,and not twisted.
Important:
7 8
PRESS
Loosening the harness
To loosen the harness, press the adjuster button at the front of the
seat under the fabric and, using the other hand simultaneously,
grab hold of the lower section of the shoulder straps (underneath
the protective padding) and pull them towards you to loosen.
IMPORTANT: Do not pull the shoulder straps by holding the
protective padding.
8.Adjust the backrest angle
Installed forward-facing or rearward facing, there are 3 recline positions available.
Pull the positioning handle under the front of the seat upwards,and then pull or push
the seat forwards or backwards.Release the positioning handle in the desired
position and push until you hear “click”.
Check to make sure the child seat is securely locked in the desired
position by pulling the positioning handle.
Important:
9.Adjust the shoulder strap height
If the height of your shoulder belts in child car seat is not fit for your
child
,
adjust the height of the shoulder belt
,
Please proceed as follows
:
Step 1
.
Loosen the shoulder harness
(
see point 7.1
)
turn the child seat
to the back
.
Slide the chest straps
and shoulder straps off the harness
connectors.
Step 2. Pull the straps through the
shoulder strap slots from the front
of the child seat.Now you can remove
the shoulder straps and chest pad.
3
2
1
1
2
3
forward facing rearward facing
CLICK
6.Usage of buckle
Firstly
,
adjust the shoulder straps height
,
please proceed as follows
:
Step1
.
Put the two metal sections of the buckle connector together
.
Step2
.
Slot the two buckle connectors into the slot in the buckle until they
click place.
Step3
.
Check the harness is correctly locked by pulling the shoulder straps
upwards
.
To release the harness
,
you can press the red button of the buckle downwards
,
the two metal sections will be pop up
.
“ ”
7.Adjust and use the harness
7.1 Loosen the harness
The harness is slackened by pressing the adjuster
(under the adjuster cover)on the front of the seat.
Press down the adjuster as you grip
the two shoulder
straps with your another hand.Pull the shoulder
straps towards you to loosen the harness.
7.2 Tighten the harness
Pull the shoulder straps upwards to remove the slack
from the lap sections of the harness then pull the
adjuster strap until the harness is fully tightened.
The harness should be adjusted as tightly as possible
without causing discomfort to your child.
A loose harness can be dangerous.Check the harness
adjuster and tighten each time the child is placed in
the seat.
CLICK
PRESS
Step 3. Then re-thread the shoulder
straps and chest straps into the
appropriate strap slots from the front
of the child seat and slide them in the
harness connectors.
Make sure that both of the
shoulder belts and chest belt go through
slots at the same height,and not twisted.
Important:
7 8
PRESS
Tightening the harness
To tighten the harness, pull the adjuster strap until the harness is nicely
tight and clings to the child’s body. Check that you can still slide your
finger between the straps and the child’s shoulder (space of 1 cm). Be
sure that the child is comfortable and protected.
8.Adjust the backrest angle
Installed forward-facing or rearward facing, there are 3 recline positions available.
Pull the positioning handle under the front of the seat upwards,and then pull or push
the seat forwards or backwards.Release the positioning handle in the desired
position and push until you hear “click”.
Check to make sure the child seat is securely locked in the desired
position by pulling the positioning handle.
Important:
9.Adjust the shoulder strap height
If the height of your shoulder belts in child car seat is not fit for your
child
,
adjust the height of the shoulder belt
,
Please proceed as follows
:
Step 1
.
Loosen the shoulder harness
(
see point 7.1
)
turn the child seat
to the back
.
Slide the chest straps
and shoulder straps off the harness
connectors.
Step 2. Pull the straps through the
shoulder strap slots from the front
of the child seat.Now you can remove
the shoulder straps and chest pad.
3
2
1
1
2
3
forward facing rearward facing
CLICK
6.Usage of buckle
Firstly
,
adjust the shoulder straps height
,
please proceed as follows
:
Step1
.
Put the two metal sections of the buckle connector together
.
Step2
.
Slot the two buckle connectors into the slot in the buckle until they
click place.
Step3
.
Check the harness is correctly locked by pulling the shoulder straps
upwards
.
To release the harness
,
you can press the red button of the buckle downwards
,
the two metal sections will be pop up
.
“ ”
7.Adjust and use the harness
7.1 Loosen the harness
The harness is slackened by pressing the adjuster
(under the adjuster cover)on the front of the seat.
Press down the adjuster as you grip
the two shoulder
straps with your another hand.Pull the shoulder
straps towards you to loosen the harness.
7.2 Tighten the harness
Pull the shoulder straps upwards to remove the slack
from the lap sections of the harness then pull the
adjuster strap until the harness is fully tightened.
The harness should be adjusted as tightly as possible
without causing discomfort to your child.
A loose harness can be dangerous.Check the harness
adjuster and tighten each time the child is placed in
the seat.
CLICK
PRESS
Step 3. Then re-thread the shoulder
straps and chest straps into the
appropriate strap slots from the front
of the child seat and slide them in the
harness connectors.
Make sure that both of the
shoulder belts and chest belt go through
slots at the same height,and not twisted.
Important:
7 8
PRESS
CAUTION!: the harness must be continually adjusted as
your child grows.
If the height of the child seat’s harness is not appropriate
for your child’s height, adjust it as follows:
Loosen the harness as shown in the “ADJUSTING THE
HARNESS” section
1. Slide the ends of both straps off the connector clip
located at the back of the child seat.
2. Pull the straps from the front until they come out of the
slots in the backrest
3. Reinsert the straps into the slots in the backrest at the
required height.
4. Now reattach the two ends to the connector clip located
at the back of the child seat.
CAUTION! Always check that the straps are properly attached to the connector clip located at the