12
I
Il seggiolino dispone di 3 posizioni di reclinazione sia che si trovi in direzione di marcia, sia che si
trovi in direzione contraria di marcia.
Per reclinare il seggiolino agire sul pulsante di regolazione posto sotto la seduta nella parte frontale
e regolare il seggiolino nella posizione desiderata, in avanti o indietro.
Una volta raggiunta la posizione, rilasciare la maniglia del meccanismo di reclinazione. Un “clic”
segnalerà l’avvenuto fissaggio.
NOTA
: assicurarsi sempre che il seggiolino sia fissato in una delle tre posizioni di reclinazione e non
si trovi mai in posizioni intermedie.
INSTALLAZIONE DELLA BASE DEL SEGGIOLINO
Press ISOFIX release button to make ISOFIX connectors
come out of the base.
Push the ISOFIX base(A3),until ISOFIX connectors are
completely locked with the connection device of car.
“CLICK”sound indicates that ISOFIX connector has been
locked(A4,A5).
When the end of ISOFIX connector turns to green,it is
locked.Shown in red, it is not locked(A4).
Adjust the length of the leg to make sure that the leg can
touch the ground of the car very steadily(A5).
12. Instructions of uninstalling the base
Press ISOFIX unlock button to release the ISOFIX
(B1,B2).
If you don’t need to use car seat,press ISOFIX adjusting button.At the same
time,another hand push ISOFIX,according to the direction of the arrow to push
can shrink ISOFIX connector(B3).
base
10.Remove the buckle and car seat pad
11. Instructions of installing the base
STEP 1:
Release the buckle(fig.1),release the shoulder belt as long as you can.
STEP 2:
(fig.2)
STEP 3:
Take out the buckle from the pad(fig.3).
Please keep the buckle and crotch pad as well.
Please adjust the seat to the biggest angle,you will see the end bracket
under the car seat.Then you can pull out the harness from the solt which under
the car seat
.
Note:
Pay attention:
if not necessary,please do not disassemble the shoulder belt.
STEP 5:
Pull all direction to take out the cover(fig.6)
★
The above steps in turn, that is the cloth cover installation method
STEP 4:
comfortable cushion,chest pad and buckle connectors(fig.5).
Slide both of the harness off the harness connector(fig.4),and take off
the
9
10
1
2
3
4
5
6
A2
A5
A6
Note:Leg not hanging in the air or other items can be used to support.At the same
time to ensure that the leg is no higher that the safety seat.Check whether leg
shows green(A6).
B2
B3
CLICK
A4
√
×
CLICK
UNLOCK
B1
PRESS
A1
A3
Press ISOFIX release button to make ISOFIX connectors
come out of the base.
Push the ISOFIX base(A3),until ISOFIX connectors are
completely locked with the connection device of car.
“CLICK”sound indicates that ISOFIX connector has been
locked(A4,A5).
When the end of ISOFIX connector turns to green,it is
locked.Shown in red, it is not locked(A4).
Adjust the length of the leg to make sure that the leg can
touch the ground of the car very steadily(A5).
12. Instructions of uninstalling the base
Press ISOFIX unlock button to release the ISOFIX
(B1,B2).
If you don’t need to use car seat,press ISOFIX adjusting button.At the same
time,another hand push ISOFIX,according to the direction of the arrow to push
can shrink ISOFIX connector(B3).
base
10.Remove the buckle and car seat pad
11. Instructions of installing the base
STEP 1:
Release the buckle(fig.1),release the shoulder belt as long as you can.
STEP 2:
(fig.2)
STEP 3:
Take out the buckle from the pad(fig.3).
Please keep the buckle and crotch pad as well.
Please adjust the seat to the biggest angle,you will see the end bracket
under the car seat.Then you can pull out the harness from the solt which under
the car seat
.
Note:
Pay attention:
if not necessary,please do not disassemble the shoulder belt.
STEP 5:
Pull all direction to take out the cover(fig.6)
★
The above steps in turn, that is the cloth cover installation method
STEP 4:
comfortable cushion,chest pad and buckle connectors(fig.5).
Slide both of the harness off the harness connector(fig.4),and take off
the
9
10
1
2
3
4
5
6
A2
A5
A6
Note:Leg not hanging in the air or other items can be used to support.At the same
time to ensure that the leg is no higher that the safety seat.Check whether leg
shows green(A6).
B2
B3
CLICK
A4
√
×
CLICK
UNLOCK
B1
PRESS
A1
A3
Premere il pulsante di sgancio per consentire l’uscita dei connettori ISOFIX
dalla base (fig. A1).
Con i connettori ISOFIX completamente estratti, fissare la base agli ancoraggi
ISOFIX del sedile del veicolo. Un “clic” segnalerà l’avvenuto fissaggio e un
indicatore di colore verde comparirà su ciascuno dei connettori ISOFIX della
base (fig. A4).
Regolare la lunghezza della gamba di appoggio premendo il pulsante di
regolazione posto sulla barra.
La gamba deve poggiare saldamente sul fondo del veicolo; un indicatore di colore verde posto nella
barra di appoggio ne segnalerà il corretto montaggio (fig. A5/A6).
Verificare che la gamba di appoggio sia bloccata, rimanga in posizione e non si muova verso l’alto
o verso il basso.
Содержание JL-1048 SECURFIX BEEP
