Jøtul GI 450 DV Katahdin, Инструкция по установке и эксплуатации

Страница: 17 / 28

17
Wall Thermostat
Use only a 75
a 75
a 75 a 75 a 750 milliv
0 milliv
0 milliv 0 milliv 0 millivolt
olt
olt olt olt DC
DC
DC DC DC tw
tw
tw tw two-wir
o-wir
o-wir o-wir o-wire cir
e cir
e cir e cir e circuit
cuit
cuit cuit cuit
thermosta thermosta
thermosta thermosta thermostattttt. The thermostat should be placed in the
same room as the heater, typically 5’ off the floor. Avoid
drafty areas or any area that may affect the accuracy of
the thermostat.
The thermostat should be connected to the
Katahdin using a minimum of 16 gauge wire with a
maximum length of 35 feet of wire.
Connect the two thermostat wire leads to the two
lower terminals on the terminal block located to the
right of the ON/OFF/TSTAT switch. Do not overtighten
the connections. IT IS NOT NECESSARY TO DISCONNECT
ANY OTHER WIRES. See Figure 20.
For the thermostat to function, the ON/OFF/T-STAT
switch must be in the T-STAT position, and the pilot light
must be running, as it is the power source for the
thermostat.
At the thermostat, the two wires should be con-
nected to the two connections screws on the thermo-
stat base plate per the manufacturer’s instructions.
Optional Remote Control
#129706
CAUTION:
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN
SERVICING THE CONTROLS. WIRING ERRORS CAN CAUSE
IMPROPER AND DANGEROUS OPERATION. ALWAYS VERIFY
PROPER OPERATION AFTER SERVICING THE APPLIANCE.
ATTENTION:
AU MOMENT DE L’ENTRETIENDES COMMANDES,
ETIQUETEZ TOUS LES FILS AVANT LE DEBRANCHEMENT.
DES ERREURS DE CABLAGE PEUVENT ENTRAIUN FONC-
TIONNEMENT INADEQUAT ET DAGEREUX.
The optional Jøtul remote can be installed on the
Katahdin gas insert. Using the wires supplied with
the remote, it is best to wire the remote directly to
the gas control valve of the insert.
Connect one receiver lead to the terminal la-
belled TH. Connect the other receiver lead to the
terminal labeled TH/TP. DO NOT DISCONNECT ANY
OTHER WIRES FROM THE VALVE, AND DO NOT OVER
TIGHTEN TERMINAL SCREWS.
Jøtul r Jøtul r
Jøtul r Jøtul r
Jøtul rec ec
ec ec
ecommends ommends
ommends ommends
ommends the use o the use o
the use o the use o
the use of f
f f
f the optional the optional
the optional the optional
the optional
R R
R R
Remote R emote R
emote R emote R
emote Rec ec
ec ec
eceiv eiv
eiv eiv
eiver Hea er Hea
er Hea er Hea
er Heattttt Shield (# 129 Shield (# 129
Shield (# 129 Shield (# 129
Shield (# 1297777708) 08)
08) 08)
08) to protect
the receiver under the firebox. The best location for
the receiver is just below the air intake port toward
the back of the unit.
Figure 19. Blower Wiring Diagram - GI 450 Katahdin
Figure 20. Wiring diagram / GI450 DV Katahdin
Place Receiver Here
Figure 21. Remote Receiver position.
TERMINAL
BLOCK
VALVE
THERMOPILE
OPTIONAL
THERMOSTAT
or
REMOTE
CONTROL
TH
TP
TH
TP
ROCKER
SWITCH
ON
OFF
STAT
Air
Intake
Port
MANUAL
OFF
AUTO
SNAPSTAT
GN
BLOWER
POWER
SUPPLY
RHEOSTAT
SWITCH
BK
GY
BK
BK
BU
BK
BK
WH