Boulevard DVLL48BP92N-1 Скачать руководство пользователя

Страница: 1 / 64

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

DIRECT VENT ZERO CLEARANCE

GAS FIREPLACE HEATER

MODEL SERIES:

MULTIFUNCTION REMOTE (MF)

DVLL48BP92(N,P)-1

DVLL60BP90(N,P)-1

GAS-FIRED

UL FILE NO. MH30033

This appliance may be installed in

an aftermarket, permanently located,

manufactured home (USA only) or mobile

home, where not prohibited by local codes.
This appliance is only for use with the type

of gas indicated on the rating plate.
This appliance is not convertible for use

with other gases, unless a certified kit is

used.

WARNING

If not installed, operated and maintained

in accordance with the manufacturer’s

instructions, this product could expose

you to substances in fuel or from fuel

combustion which can cause death or

serious illness.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death or

property damage.

— Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the fire department.

— Installation and service must be

performed by a qualified installer,

service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

WARNING

A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and shall
be installed for the protection of children and other at-risk
individuals.

NOTE:

Barrier required, may be sold separately.

Содержание DVLL48BP92N-1

































































Результаты поиска

Содержание DVLL48BP92N-1

Отзывы:

Похожие инструкции для DVLL48BP92N-1

Бренды по названию

Популярные бренды

Boulevard DVLL48BP92N-1, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVLL48BP92N-1

Отзывы:

Похожие инструкции для DVLL48BP92N-1

Бренды по названию

Популярные бренды