Kingsman ZDV3318 Series Installation Instructions Manual Download

Page: 1 / 59

Installation Instructions

ZDV3318

Model

Numbers:

ZDV3318N, ZDV3318NE, ZDV3318NE2, ZDV3318LP, ZDV3318LPE, ZDV3318LPE2

Certified to:

ANSI Z21.88-2017 • CSA 2.33-2017 Vented Gas Fireplace Heaters, CSA 2.17-2017

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

A Division of R-Co. Inc.

2340 Logan Ave.

Winnipeg, Manitoba Canada

R2R 2V3 Ph.: (204) 632-1962

Printed in Canada July 17, 2019

Part# 3318-MAN17

This appliance may be installed in an

aftermarket, permanently located,

manufactured home (USA only) or mobile

home, where not prohibited by local codes.

This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases, unless a certified kit is used.

Summary of Contents for ZDV3318 Series




























































Search results

Summary of Contents for ZDV3318 Series

Reviews:

Related manuals for ZDV3318 Series

Brands by name

Popular brands

Kingsman ZDV3318 Series, Installation Instructions Manual

Search results

Summary of Contents for ZDV3318 Series

Reviews:

Related manuals for ZDV3318 Series

Brands by name

Popular brands