Jøtul GI 450 DV Katahdin, Инструкция по установке и эксплуатации

Страница: 15 / 28

15
Flame Adjustment / Air Shutter
THE KATAHDIN GAS INSERT IS SHIPPED FROM THE
FACTORY EQUIPPED FOR USE WITH NATURAL GAS.
WHEN USING PROPANE, IT WILL BE NECESSARY TO
ADJUST THE AIR SHUTTER ON THE BURNER TUBE TO
ACHIEVE THE PROPER GAS TO AIR MIX. See fig. 15.
WARNING:
AIR SHUTTER ADJUSTMENTS SHOULD ONLY BE
PERFORMED BY A QUALIFIED PROFESSIONAL
SERVICE TECHNICIAN.
The air shutter adjustment can also help achieve
the desired flame appearance. Generally, flame appear-
ance is a matter of preference, however most consum-
ers enjoy the warm, yellowish flame.
Closing Closing
Closing Closing Closing the Air Shutter
the Air Shutter
the Air Shutter the Air Shutter the Air Shutter - Insufficient combustion
air will result in very long yellow flames that can
promote soot. Sooting produces black deposits on the
logs, on the inside walls of the appliance, and poten-
tially on the exterior termination cap.
Sooting is caused by incomplete combustion in the
flames and lack of combustion air entering the air
shutter opening.
Opening Opening Opening Opening Opening the air shutter the air shutter the air shutter the air shutter the air shutter - will generate a flame
that is blue and transparent, or an “anemic” flame. This
flame is generally more efficient, but not very attrac-
tive.
Jøtul recommends the following settings for the
Katahdin gas insert:
Pr Pr Pr Pr Propane: opane: opane: opane: opane: 1 1 1 1 1/////4” 4” 4” 4” 4” open open open open open
Na Na
Na Na Natur
tur
tur tur tural Gas:
al Gas:
al Gas: al Gas: al Gas: 1
1
1 1 1/////4”
4”
4” 4” 4” open
open
open open open
REMEMBER: Run the insert for a minimum of 15 to
20 minutes for an accurate representation of the flame
appearance. This should be done before and between
any air shutter adjustments.
T TT T To adjust o adjust o adjust o adjust o adjust the air shutter the air shutter the air shutter the air shutter the air shutter
1. Remove the burner tube and using a phillips head
screwdriver loosen the screw at the air shutter and
adjust accordingly.
2. Be sure to retighten the screw that holds the air
shutter setting.
3. Reassemble the insert including glass assembly.
Allow insert to burn 30 minutes on the HIGH setting,
observing the flame continuously.
4. If the flame appears weak, slow, or sooty, repeat the
process described above until the flame is as desired.
Installing the Log Set
NO NO
NO NO
NOT TT
T
TE: E:
E: E:
E: Install Install
Install Install
Install the optional An the optional An
the optional An the optional An
the optional Antique Brick P tique Brick P
tique Brick P tique Brick P
tique Brick Panels anels
anels anels
anels
bef bef
bef bef
befor or
or or
ore installing e installing
e installing e installing
e installing the L the L
the L the L
the Log Set og Set
og Set og Set
og Set.....
The Katahdin is equipped with a three piece log set
packaged in bubble wrap inside the firebox. The log set
must be removed from the packaging and arranged in
the unit prior to start up of the gas insert. Protect your
hands by wearing gloves to prevent skin irritation from
the ceramic fibers.
1. Unwrap each log and set on floor near unit.
2. Lift out andiron.
3. Place rear log over the rear log pins in the rear of the
firebox. The rear log should be installed with the
tapered end of the log on the right.
Figure 16. Log identification.
Burner Tube
Air Shutter
NOTE: A
IR SHUTTER SHOULD NEVER BE
LESS
THAN
1/8”
OPEN
.
Figure 15.
Cross-over Log
Pin
Rear Log
Pin
Front Log