Operation
Storage of the Machine
85
85
9811/5700-7
Storage of the Machine
Introduction
T2-074
If you will not use the machine for an extended period, you
must store the machine correctly. If you prepare the
machine carefully and apply on-going care you can
prevent deterioration and damage to the machine while it
is in storage.
Note:
JCB Dealers must check stock monthly.
Storage Area
The machine can be stored in a temperature range of:
-40°C to 54°C (-40°F to 129°F).
When possible, you must keep the machine in a dry
building or shelter.
If only an outdoor storage area is available, look for a
storage area with good drainage.
If the machine is to be out of use for an extended period,
careful preparation and on-going care will minimise the
possibility of deterioration and damage while in storage.
Prepare the Machine for Storage
T2-076
1
Clean the machine to remove all unwanted material
and corrosive products.
Dry the machine to remove solvents and moisture.
2
Apply grease to the moving parts. Refer to
Greasing
the Machine
.
3
Examine the machine for worn or damaged parts.
Replace if necessary.
4
Fill the fuel tank to prevent a build up of condensation
in the tank.
5
Examine the coolant condition. Replace if necessary.
6
Examine all fluid levels. Top up if necessary.
Put the Machine into Storage
T2-077
1
Park the machine on level, solid ground.
Park the machine in a position where the machine is
easy to get access (in case the machine does not
start at the end of the storage period).
Place suitable timbers under the machine to eliminate
direct contact with the ground.
2
Retract all rams and lower the attachments to the
ground.
3
Vent the hydraulic system.
4
Remove the starter key.
5
Apply a thin layer of grease or petroleum jelly to all
exposed ram piston rods.
6
Remove the battery. Charge the battery.
Keep the battery in warm, dry conditions. Charge the
battery periodically.
7
If you keep the machine outdoors, cover the machine
with tarpaulins or plastic sheets.
During Storage
T2-078
Operate the machine functions each week to prevent a
build up of rust in the engine and hydraulic circuits, and to
minimise deterioration of the hydraulic seals.
1
Clean the machine to remove all unwanted material
and corrosives.
Remove the grease or petroleum jelly from the ram
piston rods.
2
Install a charged battery.
3
Examine all fluid levels. Top up if necessary.
4
Start the engine.
Содержание RTFL 926
