jcb RTFL 926 Скачать руководство пользователя

Страница: 52 / 200

Operation

Drive Controls, Switches and Instruments

9811/5700-7

Warning Lights

340830-4

Fig 30.

CAUTION

If any of the audible/visual warnings operate while the
engine is running, stop the engine as soon as it is safe
to do so and rectify the fault.

4-2-1-2

Engine Oil Pressure Low

Audible/Visual. Lights if the engine oil pressure falls
too far. The light should go out a few seconds after the
engine is started.

Transmission Oil Pressure Low

Audible/Visual. Lights if the transmission oil pressure
falls too far. The light should go out a few seconds
after the engine is started.

Engine Coolant Temperature High

Audible/Visual. Lights if the engine coolant
temperature rises too far.

Transmission Oil Temperature High

Audible/Visual. Lights if the transmission oil
temperature rises too far.

Cold Start (If fitted)

Visual Only. With the starter switch in position

III

, if the

outside air temperature is -6°C (21°F) or below the

light will illuminate indicating that the manifold heater
is ON. When the light extinguish the engine is ready
to start.

Water in Fuel Indicator

Audible/Visual. Lights up when there is water in the
fuel system. Drain the water separator and engine
filter.

Direction Indicators

Visual Only. Flashes with the left and right direction
indicators. Use the direction indicators to signal
before turning the machine.

Main Beam On

Visual Only. Lights when the headlight main beams
are switched on. Switch the main beam off for
oncoming vehicles.

Park Brake Engaged

Audible/Visual. Lights if Forward or Reverse drive is
selected while the park brake is engaged.

No Charge

Audible/Visual. Lights if the battery charging circuit
fails while the engine is running. The light should go
out a few seconds after the engine is started.

Содержание RTFL 926









































































































































































































Результаты поиска

Содержание RTFL 926

Отзывы:

Похожие инструкции для RTFL 926

Бренды по названию

Популярные бренды

jcb RTFL 926, Руководство оператора

Результаты поиска

Содержание RTFL 926

Отзывы:

Похожие инструкции для RTFL 926

Бренды по названию

Популярные бренды