jcb RTFL 926 Скачать руководство пользователя

Страница: 114 / 200

Routine Maintenance

Prepare the Machine for Maintenance

104

9811/5700-7

Prepare the Machine for Maintenance

Introduction

WARNING

Maintenance must be done only by suitably qualified
and competent persons.

Before doing any maintenance make sure the machine
is safe, it should be correctly parked on level ground.

To prevent anyone starting the engine, remove the
starter key. Disconnect the battery when you are not
using electrical power. If you do not take these
precautions you could be killed or injured.

8-3-1-1

Make the machine safe before you start a maintenance
procedure.

You can complete most of the maintenance procedures
with the mast lowered (Position

). Unless a maintenance

procedure instructs you differently, you must lower the
mast. Refer to

How to Make the Machine Safe (Mast

Lowered)

If you lift the mast to get access for maintenance (Position

), you must install the mast chains on the mast. Refer to

How to Make the Machine Safe (Mast Lifted)

T047230

Fig 69.

Содержание RTFL 926









































































































































































































Результаты поиска

Содержание RTFL 926

Отзывы:

Похожие инструкции для RTFL 926

Бренды по названию

Популярные бренды

jcb RTFL 926, Руководство оператора

Результаты поиска

Содержание RTFL 926

Отзывы:

Похожие инструкции для RTFL 926

Бренды по названию

Популярные бренды