Introduction
Safety Check List
13
13
9811/5700-7
!M
CAUTION
'O' rings, Seals and Gaskets
Badly fitted, damaged or rotted 'O' rings, seals and
gaskets can cause leakages and possible accidents.
Renew whenever disturbed unless otherwise
instructed. Do not use Triochloroethane or paint
thinners near 'O' rings and seals.
INT-3-2-12
!M
WARNING
Hydraulic Hoses
Damaged hoses can cause fatal accidents. Inspect the
hoses regularly. Do not use the machine if a hose or
hose fitting is damaged.
INT-3-3-2_4
!M
CAUTION
Waxoyl contains turpentine substitute which is
flammable. Keep flames away when applying Waxoyl.
Waxoyl can take a few weeks to dry completely. Keep
flames away during the drying period.
Do not weld near the affected area during the drying
period. Take the same precautions as for oil to keep
Waxoyl off your skin. Do not breathe the fumes. Apply
in a well-ventilated area.
5-3-1-9
!M
WARNING
Working Under the Machine
Make the machine safe before getting beneath it.
Ensure that any fitments on the machine are secure;
engage the park brake, remove the starter key,
disconnect the battery.
INT-3-3-8_2
!M
WARNING
Certain seals and gaskets (e.g. crankshaft oil seal) on
JCB machines contain fluoroelastomeric materials
such as Viton
®
, Fluorel
TM
and Technoflon
®
.
Fluoroelastomeric materials subjected to high
temperatures can produce highly corrosive
hydrofluoric acid. THIS ACID CAN SEVERELY BURN.
New fluoroelastomeric components at ambient
temperature require no special safety precautions.
Used fluoroelastomeric components whose
temperatures have not exceeded 300°C (572°F) require
no special safety precautions. If evidence of
decomposition (e.g. charring) is found, refer to the
next paragraph for safety instructions DO NOT TOUCH
COMPONENT OR SURROUNDING AREA.
Used fluoroelastomeric components subjected to
temperatures greater than 300°C (572°F) (e.g. engine
fire) must be treated using the following safety
procedure. Make sure that heavy duty gloves and
special safety glasses are worn:
1
Thoroughly wash contaminated area with 10%
calcium hydroxide or other suitable alkali
solution, if necessary use wire wool to remove
burnt remains.
2
Thoroughly wash contaminated area with
detergent and water.
3
Contain all removed material, gloves etc. used in
this operation in sealed plastic bags and dispose
of in accordance with Local Authority
Regulations.
DO NOT BURN FLUOROELASTOMERIC MATERIALS.
INT-3-3-5_4
!M
WARNING
Protect your eyes when grinding metal. Wear safety
glasses or goggles. Remove or protect any
combustible materials from the area which could be
ignited by sparks.
GEN-1-12
Содержание RTFL 926
