Routine Maintenance
Forks
160
160
9811/5700-7
Installation
Note:
Make sure that you install the correct type of fork for
the type of carriage fitted. Do not attempt to fit the incorrect
forks.
1
Park the machine on solid level ground. Make sure
the park brake is engaged and select neutral.
2
Position the fork so that the upper hook
D
can engage
the top of the carriage
E
.
K
Fig 126. (
T
159)
3
Raise the carriage to locate the bottom hook
B
in the
lower removal notch
C
.
K
Fig 126. (
T
159)
4
Make sure each fork has engaged the carriage at the
top and bottom positions. Slide each fork along the
carriage, away from the lower removal notch
C
.
K
Fig 126. (
T
159)
!M
WARNING
If the fork/locking pin is not fully engaged, the fork
could become unintentionally disengeged.
12-6-1-13
5
Re-engage locking pins
A
into the required notches.
6
Install the locking clamp
X
onto the bottom of the
carriage.
K
Fig 126. (
T
159)
.
Industrial Carriage Fork Adjustment (
Important:
The locking clamp must be fastened to the
carriage at all times during machine operation.
Bar Carriage Forks
Removal
1
Remove the location pins
A
.
K
Fig 127. (
T
160)
2
Release the retaining clips
G
from the bar securing
pins and remove the bar
H
from the carriage.
K
Fig 127. (
T
160)
3
Using suitable lifting equipment, support the fork and
slide it to the end of the carriage.
4
Use the lifting equipment, remove the fork from the
carriage.
T069180-2
Fig 127. Bar Type Carriage
Installation
Note:
Make sure that you install the correct type of fork for
the type of carriage fitted. Do not attempt to fit the incorrect
forks.
1
Park the machine on solid level ground. Make sure
the park brake is engaged and select neutral.
2
Position the fork so that the upper hook
D
and bottom
hook
D
can engage the end of the carriage.
K
Fig 126. (
T
159)
3
Using the lifting equipment, support the fork and slide
it along the carriage.
4
Install the bar
H
onto the top of the carriage and
secure into position with retaining clips
G
.
K
Fig 127. (
T
160)
5
Make sure that each fork has engaged the carriage
correctly at the top and bottom positions.
6
Refit the two pairs of retaining pins
A
using one pair
for each fork. Make sure that each pin drops freely
into place and that each pair of pins is positioned as
shown.
K
Fig 127. (
T
160)
.
Bar Carriage Fork Adjustment (
G
H
A
A
H
Содержание RTFL 926
