jcb RTFL 926 Скачать руководство пользователя

Страница: 155 / 200

Routine Maintenance

Fuel System

145

9811/5700-7

Changing the Engine Fuel Filter Element

Get access to the Water Separator and Engine Fuel
Filter. Refer to

Water Separator and Engine Fuel

Filter, Introduction

Thoroughly clean the outside of the filter housing and
around the filter head.

Loosen the drain tap

and allow the fuel to drain into

a suitable container.

Remove the low pressure fuel lines

and

. Mark the

pipes prior to removal to ensure they are refitted in the
correct position.

Loosen the filter strap retaining screw

and lift the

filter clear.

Fit new filter element

, make sure that the filter is in

the correct position to enable connection of the fuel
lines. Torque tighten the filter strap retaining screw

to 24Nm (17.7lbf ft).

Reconnect the fuel lines

and

Fig 110. (

145)

Bleed the fuel system.

Bleeding the Fuel

System (

146)

Fig 110.

Содержание RTFL 926









































































































































































































Результаты поиска

Содержание RTFL 926

Отзывы:

Похожие инструкции для RTFL 926

Бренды по названию

Популярные бренды

jcb RTFL 926, Руководство оператора

Результаты поиска

Содержание RTFL 926

Отзывы:

Похожие инструкции для RTFL 926

Бренды по названию

Популярные бренды