jcb RTFL 926 Скачать руководство пользователя | Manualshive

Страница: 19 / 200

background image

Introduction

Safety Check List

9

9

9811/5700-7

!M

DANGER

Working Platform

Using the machine as a working platform is
hazardous; you can fall off and be killed or injured.
Never use the machine as a working platform.

5-1-5-9

!M

WARNING

Machine Safety

Stop work at once if a fault develops. Abnormal
sounds and smells can be signs of trouble. Inspect
and repair before resuming work.

8-1-2-3

!M

WARNING

Touching hot surfaces can burn skin. The engine and
machine components will be hot after the unit has
been running. Allow the engine and components to
cool before servicing the unit.

10-1-1-40

!M

WARNING

Travelling at High Speeds

Travelling at high speeds can cause accidents. Do not
reverse in a high gear with full throttle. Always travel
at a safe speed to suit working conditions.

INT-5-3-3

!M

WARNING

The engine has exposed rotating parts. Switch OFF the
engine before working in the engine compartment. Do
not use the machine with the engine cover open.

5-2-6-5

!M

WARNING

You could be killed or seriously injured if you operate
a machine with a damaged or missing ROPS/FOPS. If
the Roll Over Protection Structure (ROPS)/Falling
Objects Protection Structure (FOPS) has been in an
accident, do not use the machine until the structure
has been renewed. Modifications and repairs that are
not approved by the manufacturer may be dangerous
and will invalidate the ROPS/FOPS certification.

INT-2-1-9_6

!M

CAUTION

Fork Spacing

Loads can fall off incorrectly spaced forks. Always
space the forks correctly for the load. Make sure the
forks are completely under the load before lifting.

5-1-4-2

!M

CAUTION

One-Fork Lifting

A load lifted on one fork can slip off. Never lift a load
with one fork.

5-1-4-3

!M

CAUTION

Unloading

Never unload the forks by stopping the machine
suddenly. Follow the procedures in the Operator
Manual for unloading.

5-1-4-4_2

!M

CAUTION

Uneven Ground

Loads stacked on uneven ground can topple. Never
stack loads on uneven ground.

5-1-4-5

!M

WARNING

Scaffolding

Overloaded scaffolding can collapse. Never load
scaffolding beyond the regulation capacity.

5-1-4-6

!M

CAUTION

Overhead Clearance

A raised mast can strike overhead objects. Always
check for overhead clearance before raising the mast.

9-1-3-1

!M

WARNING

Mast/Travelling

Operating the mast and carriage while travelling can
cause accidents. You will not have total control. Never
operate the mast and carriage while travelling.

9-1-3-2

«
...
17
18
19
20
21
...
»

Содержание RTFL 926









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RTFL 926

Бренд: Jungheinrich Страницы: 79

Бренд: AUSA Страницы: 51

Бренд: Manitou Страницы: 21

Бренд: Manitou Страницы: 116

Бренд: Crown Страницы: 19

Бренд: Vestil Страницы: 22

LOGIFLEX SELF 1001

Бренд: logitrans Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды