jcb JS130 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 533

jcb JS130 Скачать руководство пользователя страница 40

4 - 1

First Aid - Electrolyte

EYES

FLUSH WITH WATER FOR 15 MINUTES. GET MEDICAL
HELP FAST.

IF SWALLOWED

DO NOT INDUCE VOMITING. DRINK LARGE QUANTITIES
OF WATER OR MILK. Then drink milk of magnesia, beaten
egg or vegetable oil.

SKIN

FLUSH WITH WATER. REMOVE AFFECTED CLOTHING.

!

!

WARNING

Batteries give off an explosive gas. Do not smoke when
handling or working on the battery. Keep the battery
away from sparks and naked flames.

Battery electrolyte contains sulphuric acid. It can burn
you if it touches your skin or eyes. Wear goggles.
Handle the battery carefully to prevent spillage.

Keep metallic items (watches, rings, zippers etc) away
from the battery terminals. Such items could short the
terminals and burn you.

Set all switches in the cab to OFF before disconnecting
the battery. When disconnecting the battery, take off the
earth (-) lead first.

When reconnecting, fit the positive (+) lead first.

Re-charge the battery away from the machine, in a well-
ventilated area. Switch the charging circuit off before
connecting or disconnecting the battery. When you have
installed the battery in the machine, wait five minutes
before connecting it up.

5-3-4-3

!

!

CAUTION

Do not disconnect the alternator, the battery, or any part
of the charging circuit with the engine running.

8-3-4-1

Charge Rate Depending on the Battery specific Gravity

If the battery is charged and the charge rate is less than
75%, replace the battery.

Check the Electrolyte Level

1

Open the Battery Compartment A

Remove the bolts securing the metal plate above the

battery. Remove the plate.

2

Check the Level

Remove covers and look at the level in each cell. The
electrolyte should be 6 mm. (0.25 inch) above the
plates. Top up if necessary with distilled water or

de-ionized water.

!

!

WARNING

Do not top the battery up with acid. The electrolyte could
boil out and burn you.

2-3-4-6

3

Check the Connections

Make sure that the terminals are tight and clean. Coat

them with petroleum jelly to prevent corrosion.

Section 3

Routine Maintenance

9803/6410

Section 3

4 - 1

Issue 1

Battery

Temperature

20°C

0°C

-10°C

Charge Rate

100% (satisfactory)

1.26

1.27

1.28

90% (satisfactory)

1.24

1.25

1.26

80% (charge)

1.22

1.23

1.24

75% (charge)

1.21

1.22

1.23

«
...
38
39
40
41
42
...
»

Содержание JS130






















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов