manualshive.com logo in svg

jcb JS130, Руководство по обслуживанию

Поделиться
Скачать
jcb JS130 Скачать руководство пользователя страница 321

41 - 2

Section E

Hydraulics

9803/6410

Section E

41 - 2

Issue 1

Remote Control Valve (Services)

Dismantling and Assembly (cont’d)

Dismantling (cont’d)

7

Remove mounting screws (4 off) and lift out control
valve.

8

Clean the valve exterior using approved solvent and
using soft metal pads for protection, clamp the valve
body into a vice.

9

If the return springs 

15 

are weak, the sliding resistance

of the seal 

9 

will cause the guides 

8 

to stick in the

casing. Using a screw driver, carefully ease out the
guides 

8 

and plungers 

11

.

Note: 

Care must be taken to prevent damage to the guides

when removing. Ensure the guides do not fly out due to the
force of the return springs.

10

Remove spring seats

13

, split washers 

12

, return

springs 

15

, pressure control springs 

14 

and spools 

17

.

Note: 

Identify each set of parts and their locations for

assembly.

11

Slacken and remove body assembly screw 

6

. Remove

and discard ‘O’-ring 

7

.

12

Separate upper and lower body sections 

1 

and 

2 

and

remove dowel pins 

5

.

13

Remove and discard ‘O’-rings 

3

and 

4

.

14

Hold spools 

17 

firmly on the work bench and depress

spring seat 

13 

and remove split washers 

12

.

Note: 

Avoid scratching the surface of the spools. Do not

depress the spring seats more than 6 mm (0.24 in).

15

Separate spools 

17

, spring seats 

13

, springs 

14 

and 

15

and shims 

16

.

16

Remove plungers 

11 

from guides 

8

.

17

Remove seals 

9 

and 

10 

from guide 

8 

and discard.

Note: 

Leave all parts to soak in suitable solvent until dirt is

loosened. Using clean solvent wash all parts and allow to air
dry. Apply rust inhibitor to all parts.

Содержание JS130






















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды