Japan Radio Co. JAX-9B Скачать руководство пользователя страница 90

Страница: 90 / 118

Chapter 5 Maintenance

5.4

Troubleshooting

If JAX-9B has a failure, it should be diagnosed by an authorized service engineer to replace any
defective part. However, the user can shoot the simple troubles referring to the table below.

Trouble symptom

Cause

Action

Refer to

Paper feed and
recording are
impossible.

The recording paper is tilted or
slackened and deviated from the
paper sensor.

Set the recording paper properly.

P69

Unlocked the top cover.
(Mechanism part with the thermal
head)

Push down the top cover firmly
until it is locked with a click.

P71

The paper sensor (left below the
rubber roller) is contaminated with
paper dust.

Clean the paper sensor carefully.

P72

Recording does not
start.

The parameter SCAN SPEED is
erroneous.

Adjust the SCAN SPEED.

P37

The receiving condition is no good.

Change the frequency to the good
receiving condition.

P24

The register operation of a timer
program has not been completed.
The display of LCD is still a
program mode.

Press the [PROG] switch.
The timer program mode is
finished.

P47

Printing becomes
blurred or falls out.

The thermal head is not cleaned.

Clean the thermal head.

P72

The timer program
receiving does not
start.

"Clock Error!!" is displayed when
JAX-9B is powered on.

Set the correct time.
Replace the backup battery.

P63
P73

The internal clock is set an incorrect
time.

Set the correct time.

P63

The POWER switch is switched
over from OFF to TIMER.

Set the POWER switch to ON
before setting it to TIMER.

P50

The program contents contain any
errors.

Check the timer program list by
printing.
Correct the program.

P54
P52

The receiving start time is
overlapped for two or more
programs.

Check the "ERROR" message in
the printed timer program list.
Correct the program with "NG"
message

P54
P52

Содержание JAX-9B























































































































Результаты поиска

Содержание JAX-9B

Отзывы:

Japan Radio Co. JAX-9B, Инструкция по эксплуатации, Страница: 90 / 118

Результаты поиска

Содержание JAX-9B

Отзывы: