Japan Radio Co. JAX-9B Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 118

Japan Radio Co. JAX-9B Скачать руководство пользователя страница 85

Chapter 5 Maintenance

71

5.

Chapter 5 Maintenance

Do not attempt inspections or repairs on the internal part of the equipment by yourself.
Inspections or repairs by anyone other than qualified maintainers may result in a fire or an
electric shock.
Ask for internal inspections or repairs of the equipment to the Sales Department of JRC, the
nearest branch company, branch office, sales office, or any agents of Japan Radio Co., Ltd.

5.1

Replacing Recording Paper

Use the recording paper (6ZPTS00108) as specified by JRC.
The use of any other unspecified paper may cause recording density blurs, abnormal paper
feed, much dust, resulting in the damage of the recording device.

Do not store the recording paper in a place exposed to a high temperature, high humidity or
direct sunlight. Otherwise, recording density blurs may be caused.

When the remaining section of the recording paper is approximately 2m long, a red ending mark appears
on it. Then, prepare for replacing the recording paper.
JAX-9B automatically stops when the recording paper is used out, and end-of-paper message appears on
the LCD.

Procedure of replacing recording paper

1) Turn off the power of JAX-9B.

«
...
83
84
85
86
87
...
»

Содержание JAX-9B























































































































Отзывы:

Нет отзывов