Japan Radio Co. JAX-9B Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 118

background image

Chapter 3 Installation

17

6) Mount the mounting base with four M5 bolts or four wood screws.

7) Reverse the above steps to remount the facsimile body and set the recording paper roll in it.

8) Connect the antenna cable, the power cable, and the earth.

Connect the BK input cable, AF input cable of the external receiver, and the GPS data input cable if
needed.
Refer to 3.7 for wiring details.

NOTE

•

The AF signal of external receiver and the BK signal have a polarity. Be careful in

connecting them to JAX-9B.

• If a transceiver is installed, connect the BK signal cable from the

transceiver to JAX-9B.

MEMO

•

“BK” is an abbreviation of “BREAK”, which means the disconnection of the

antenna from JAX-9B.
If JAX-9B is installed with a radio transmitting equipment such as a HF
transceiver, the BK signal sent from the transceiver disconnects the antenna from
JAX-9B and protects the internal receiver against the transmitting radio waves
from the transceiver.

«
...
29
30
31
32
33
...
»

Содержание JAX-9B























































































































Отзывы:

Нет отзывов

Похожие инструкции для JAX-9B

Бренд: Harman Kardon Страницы: 13

Бренд: Jensen Страницы: 12

VM9213 - Touch Screen MultiMedia Receiver

Бренд: Jensen Страницы: 62

Бренд: Jensen Страницы: 9

Бренд: Jensen Страницы: 22

JHD3510 - Heavy Duty CD Receiver

Бренд: Jensen Страницы: 2

VM8013HD - Screen MultiMedia Receiver

Бренд: Jensen Страницы: 78

Phase Linear UV10

Бренд: Jensen Страницы: 90

Бренд: Teac Страницы: 36

Бренд: Strong Страницы: 25

Бренд: DMP Electronics Страницы: 4

Centronic VarioControl VC420

Бренд: Becker Страницы: 52

Бренд: Blaupunkt Страницы: 2

Бренд: Yaesu Страницы: 77

Бренд: Eonon Страницы: 16

Бренд: Hallicrafters Страницы: 9

Бренд: Alpine Страницы: 36

Бренд: National Instruments Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды