background image

 

Precautions

 

 

vi 

 
 

 

 

Turn on or off the POWER switch after waiting more than one second.     
Turning it back ON right after being turned OFF in no time may cause the equipment 
malfunction. 

 

Clean the thermal head with a piece of soft cloth always.    Do not rub it with a screw driver or 
file.    Otherwise, it destroys the thermal head. 

 

Do not replace the backup battery by customers. 
Even if the POWER switch on the equipment is turned OFF, some parts may remain 
electrically charged, causing an electric shock or malfunction. 
Request replacing the backup battery to the sales department of JRC, a nearby branch office, 
business office, or any agents of JRC. 

 

Use the JRC-specified backup battery (CR2032-type lithium battery).     
The use of any unspecified battery may cause a malfunction or failure of the equipment. 

 

 

 

The prohibited matters over lithium battery are as follows; 
• Short-circuit of electrodes, • Any unspecified uses of battery, •Decomposing, •Converting, • 
Discarding, •Throwing into the fire, •Heating, • Use of battery that passes exchange time. 
Otherwise, these may cause following trouble; 

• Electrolyte leakage, •Generation of Heat, •Fire •Explosion, •Destruction, •Burn

 

 

In returning used lithium battery to JRC, take the isulating treatment such as attaching a tape 
to the +/– terminals.    If the battery is short-circuited with no insulating treatment, it may 
cause a heat, explosion or fire. 

 

Do not conduct operations with wet hands. 
Otherwise, it may cause an electric shock. 

 

Turn off power supply switch before opening the top cover to replace the recording paper. 
Otherwise, it may cause an electric shock, malfunction, or burn. 

Содержание JAX-9B























































































































Отзывы: