IPS VX121P Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 68

background image

VX121P/151P/171P(-QM57)

User’s manual rev.0.0 (Preliminary)

MU-C656.xxxxxxxxxx r.0.0-EN

9 of 68

Caution
If the LCD display glass breaks, avoid contact with the liquid that may
leak out. If the liquid crystal material leaks from the panel, it should be
kept away from eyes or mouth. In case of contact it must be washed

away immediately and thoroughly with water then consult a doctor.
In case of contact with hands, legs or clothes, it must be washed
away immediately and thoroughly with water and soap.

Warning
The power cord (115/230Vac version) must be connected to an outlet
with protective earthing.
Failure to follow this warning could result in severe electrical shock.

1.3 Battery

The Panel PC contains a lithium battery. The batteries must be replaced by an
authorized qualified technical only.

Warning
Danger of explosion and harmful material emission if lithium battery is
incorrectly  replaced.  Replace  only  with  the  same  or  equivalent  type
recommended  by  the  manufacturer.  The  battery  module  contains

lithium. Do not attempt to dispose of it in a fire or incinerator, do not
overheat up to 80°C, do not short-circuit, do not i nvert poles, do not
disassemble it: the battery may explode.
Don’t try to recharge the lithium battery, the battery may explode.
Don’t allow the battery to come in contact with water.
Always follow regulations in your area for lithium battery disposal.

1.4 Application permitted

The  Panel  PC  use  is  permitted  as  stationary  equipment  for  building-in  for  indoor
applications in an industrial environment.
The equipment is suitable for use as Human Machine Interface (HMI).
Because  of  the  variety  of  uses  for  the  Panel  PC  those  responsible  for  the
application  and  use  of  this  Panel  PC  must  satisfy  themselves  that  all  necessary
steps  have  been  taken  to  assure  that  each  application  and  use  meet  all
performance, safety requirements, including any applicable laws, regulations and
standards. Following the results of a risk analysis, additional protection equipment
on the machine or the system is necessary to avoid endangering persons.

«
...
7
8
9
10
11
...
»

Содержание VX121P





































































Отзывы:

Нет отзывов

Похожие инструкции для VX121P

Бренд: AUO Страницы: 19

Бренд: I-Tech Страницы: 25

kontron FlatView HYG

Бренд: S&T Страницы: 35

130 WATT CRYSTALLINE SOLAR PANEL

Бренд: Sunforce Страницы: 10

Touch ST UHD-AND-K-005 Series

Бренд: Speechi Страницы: 30

GPSMAP 1222 TOUCH

Бренд: Garmin Страницы: 8

VITOSOL 100-F SV1B

Бренд: Viessmann Страницы: 4

Touch Panel Computer TPC-2012

Бренд: National Instruments Страницы: 49

Бренд: Innuera Страницы: 46

Бренд: Insignia Страницы: 93

Бренд: YASKAWA Страницы: 53

Бренд: Interlogix Страницы: 2

Бренд: IEI Technology Страницы: 101

Бренд: ubbink Страницы: 9

DIGITRONIK SDC40A

Бренд: Yamatake Страницы: 66

Бренд: Omega Страницы: 20

Бренд: RCA Страницы: 120

Бренд: Qeedji Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды